Post your Cinebench R20+15+R11.5+2003 Scores **Don't Read The OP PLZ**

[KeltonDSMer]

@Jumper118

 

So no luck with the earlier bios versions, but I found a thread over on Asrock's forum with a guy having the EXACT same issue with his g4400 on the same board and replied to his own thread saying bios 2.8 fixed the issue. Tried that, and things are looking good! Voltage remained unlocked above 100MHz bclk and I should get some better clocks now.

 

How hot do you guys let the chip/socket get? I am seeing ~70c on chip and socket at the end of r15 at stock clocks/1.26V, so I figure I'm probably still below 80c at the same voltage at higher clocks. Does this seem like a reasonable assumption?

 

The LLC is terrible on this board or flat out just doesn't work btw, 1.3v drops to 1.26 on the highest LLC setting in r15...on a 60W tdp chip lol

 

 

[Jumper118]

1 minute ago, KeltonDSMer said:

@Jumper118

 

So no luck with the earlier bios versions, but I found a thread over on Asrock's forum with a guy having the EXACT same issue with his g4400 on the same board and replied to his own thread saying bios 2.8 fixed the issue. Tried that, and things are looking good! Voltage remained unlocked above 100MHz bclk and I should get some better clocks now.

 

How hot do you guys let the chip/socket get? I am seeing ~70c on chip and socket at the end of r15 at stock clocks/1.26V, so I figure I'm probably still below 80c at the same voltage at higher clocks. Does this seem like a reasonable assumption?

 

The LLC is terrible on this board or flat out just doesn't work btw, 1.3v drops to 1.26 on the highest LLC setting in r15...on a 60W tdp chip lol

 

 

that is good to hear you found a solution. in r15 its fine to let it get to 85c, but daily you need to use a stress test program to check the temps. also how are you reading the cpu temps, because you shouldnt be able to on anything i am aware of other the oc formula drive and an msi post code readout? 

[KeltonDSMer]

10 minutes ago, Jumper118 said:

that is good to hear you found a solution. in r15 its fine to let it get to 85c, but daily you need to use a stress test program to check the temps. also how are you reading the cpu temps, because you shouldnt be able to on anything i am aware of other the oc formula drive and an msi post code readout? 

 

Sorry my explanation wasn't very good of the temp thing. Since I can't read temps above stock clocks, I am just cranking the voltage at stock to see how hot it gets in r15 and "guessing" how much it will increase with clocks at the same voltage Obviously they will go a bit higher with clocks, but it at least gives me an idea of what the voltage/heat curve looks like.

 

I'm pretty familiar with skirting on the edge of "too hot", those 8320 scores of mine in the doc are on a hyper 212 evo at 4.88GHz lol

 

Turns out the mem controller wasn't the issue either, no problem booting and running r15 at 2760MHz with loose timings and 1.25v on the dimms with the new bios.

 

I'm at 179/455cb so far, let's see how far it will go!

[Jumper118]

1 minute ago, KeltonDSMer said:

 

Sorry my explanation wasn't very good of the temp thing. Since I can't read temps above stock clocks, I am just cranking the voltage at stock to see how hot it gets in r15 and "guessing" how much it will increase with clocks at the same voltage Obviously they will go a bit higher with clocks, but it at least gives me an idea of what the voltage/heat curve looks like.

 

I'm pretty familiar with skirting on the edge of "too hot", those 8320 scores of mine in the doc are on a hyper 212 evo at 4.88GHz lol

 

Turns out the mem controller wasn't the issue either, no problem booting and running r15 at 2760MHz with loose timings and 1.25v on the dimms with the new bios.

 

I'm at 179/455cb so far, let's see how far it will go!

nice one. you could actually try installing oc formula drive. its made for the formula boards but it might let you read the temps correctly, just dont use it to change any settings  i was also going to say most of my bclk chips were doing 3200-3600mhz on my poo msi board so on an asrock board you should have no memory issues.

[KeltonDSMer]

3 minutes ago, Jumper118 said:

nice one. you could actually try installing oc formula drive. its made for the formula boards but it might let you read the temps correctly, just dont use it to change any settings  i was also going to say most of my bclk chips were doing 3200-3600mhz on my poo msi board so on an asrock board you should have no memory issues.

What voltage do you run your ddr4 at? I have a little extra cooling with the top down flow from the stock cooler but just failed a boot at 28xx MHz, dropped the divider and am back in windows at 27xx

[Jumper118]

3 minutes ago, KeltonDSMer said:

What voltage do you run your ddr4 at? I have a little extra cooling with the top down flow from the stock cooler but just failed a boot at 28xx MHz, dropped the divider and am back in windows at 27xx

i was running 1.45v-1.75v depending on the timings. my ram is 3866 XMP and does over 4300mhz though  

[Hal_9000]

My 5820k @4.0Ghz with 16Gb of DDR4 @3000Mhz got 1069 not the worst. Not to bad considering the moderate OC and temps rarely go above 60 degrees under load. 

[Jumper118]

1 minute ago, Hal_9000 said:

My 5820k @4.0Ghz with 16Gb of DDR4 @3000Mhz got 1069 not the worst. Not to bad considering the moderate OC and temps rarely go above 60 degrees under load. 

screenshot with cpuz? 

[KeltonDSMer]

22 minutes ago, Jumper118 said:

i was running 1.45v-1.75v depending on the timings. my ram is 3866 XMP and does over 4300mhz though  

Nice, yeah these are just bargain bin 2x8GB dimms I got at microcenter for $45 plus tax last summer. They are Crucials rated at 2400MHz cl16

 

Well, just got to the limits. I pushed more volts than I wanted, but again with the useless LLC on this board I wasn't actually running as high of voltage as in the screenshot under load. I need to get this memory under control and should be able to break 190cb in R15 single thread, but this will have to do for now (sorry for the resolution, the 2nd monitor isn't even on?):

 

481/189cb R15

Spoiler

 

"Ghetto Fabulous":

 

Spoiler

 

[Hal_9000]

7 minutes ago, Jumper118 said:

screenshot with cpuz? 

Sorry closed it after the test 

 

1020 is the best I could get after running it a few times.

[Jumper118]

1 minute ago, KeltonDSMer said:

Nice, yeah these are just bargain bin 2x8GB dimms I got at microcenter for $45 plus tax last summer. They are Crucials rated at 2400MHz cl16

 

Well, just got to the limits. I pushed more volts than I wanted, but again with the useless LLC on this board I wasn't actually running as high of voltage as in the screenshot under load. I need to get this memory under control and should be able to break 190cb in R15 single thread, but this will have to do for now (sorry for the resolution, the 2nd monitor isn't even on?):

 

481/189cb R15

  Hide contents

 

 

"Ghetto Fabulous":

 

  Hide contents

 

 

idk if i'm being a noob but i cant see the image properly. its too small.  

 

1 minute ago, Hal_9000 said:

Sorry closed it after the test 

 

1020 is the best I could get after running it a few times.

 

thats better. you going to overclock it at all? thats slower than a quickish 6700K atm. 

[Hal_9000]

2 minutes ago, Jumper118 said:

thats better. you going to overclock it at all? thats slower than a quickish 6700K atm. 

I've thought about it and I may tweek it a bit more tomorrow just to go for a better score. 

[KeltonDSMer]

2 minutes ago, Jumper118 said:

idk if i'm being a noob but i cant see the image properly. its too small.  

 

thats better. you going to overclock it at all? thats slower than a quickish 6700K atm. 

 

Yeah window's scaling makes r15 and other programs super blurry, but it is hard to click on shit at 3840x2160 without it .

 

Can you copy the image from the photobucket link and zoom in with paint or something? Still not very clear, but definitely readable. Need some anti-aliasing with this damn text scaling!

 

If not, I'm sure I'll run again with better memory values and get some r11.5 and 2003 scores too. I guess I could disable the 2nd screen in windows so the shot is 16:9 too, should look way better.

 

[Jumper118]

5 minutes ago, Hal_9000 said:

I've thought about it and I may tweek it a bit more tomorrow just to go for a better score. 

you really should, you pay extra for x99 so make sure you use that extra power to its full potential. 

4 minutes ago, KeltonDSMer said:

 

Yeah window's scaling makes r15 and other programs super blurry, but it is hard to click on shit at 3840x2160 without it .

 

Can you copy the image from the photobucket link and zoom in with paint or something? Still not very clear, but definitely readable. Need some anti-aliasing with this damn text scaling!

 

If not, I'm sure I'll run again with better memory values and get some r11.5 and 2003 scores too. I guess I could disable the 2nd screen in windows so the shot is 16:9 too, should look way better.

 

yeah even if i download the image its tiny. its 1024x384

[KeltonDSMer]

1 minute ago, Jumper118 said:

you really should, you pay extra for x99 so make sure you use that extra power to its full potential. 

yeah even if i download the image its tiny. its 1024x384

Holy shit, it is! Umm, can I upload the 5760x2160 jpeg to LTT, how does that work?

[Jumper118]

Just now, KeltonDSMer said:

Holy shit, it is! Umm, can I upload the 5760x2160 jpeg to LTT, how does that work?

yes i think you can it will compress it but not too much  you have to go to your profile, then alblums the upload image the find it in your folding and just drag it in. then it will compress it a bit then you continue. then you open it up once its done then just copy and paste it in you post. 

[KeltonDSMer]

Spoiler

 

Did this work @Jumper118  ? I honestly am the biggest noob ever, I don't even have a Facebook or Twitter account so this is foreign territory for me D:

 

I just play games and work on cars

[Jumper118]

Just now, KeltonDSMer said:

  Hide contents

 

 

Did this work @Jumper118  ? I honestly am the biggest noob ever, I don't even have a Facebook or Twitter account so this is foreign territory for me D:

 

I just play games and work on cars

i dont facebook or twitter either. It worked i can just about make it out ok now  

 

i will update the sheet while my ssd is confused as to why its gone from dual 1366 xeons and 1 gpu to x99 with 3 gpu's 

[KeltonDSMer]

1 minute ago, Jumper118 said:

i dont facebook or twitter either. It worked i can just about make it out ok now  

 

i will update the sheet while my ssd is confused as to why its gone from dual 1366 xeons and 1 gpu to x99 with 3 gpu's 

Sweet, glad you can read it. No worries on updating the doc, I'm sure I'll pester you in a week or two with 2 more points and some 11.5/2003 numbers anyway!

 

Thanks for convincing me earlier that my voltage issue was likely the mobo/bios. I have been hesitating to update my bios since Asrock specifically state which versions have microcode updates (I stayed away from them until today), but I wouldn't have found the forum post with the guy claiming ver2.80p for my board fixed the same issue unless you pointed me in that direction!

[Jumper118]

2 minutes ago, KeltonDSMer said:

Sweet, glad you can read it. No worries on updating the doc, I'm sure I'll pester you in a week or two with 2 more points and some 11.5/2003 numbers anyway!

 

Thanks for convincing me earlier that my voltage issue was likely the mobo/bios. I have been hesitating to update my bios since Asrock specifically state which versions have microcode updates (I stayed away from them until today), but I wouldn't have found the forum post with the guy claiming ver2.80p for my board fixed the same issue unless you pointed me in that direction!

you are welcome. i think you need 500cb  

[agent_x007]

Small update on legendary AMD FX CPU that could... run Crysis Windows 10 x64
Athlon 64 FX-62 @ 3,18 GHz

2003 :


R11.5


R15 :

[Jumper118]

12 minutes ago, agent_x007 said:

Small update on legendary AMD FX CPU that could... run Crysis Windows 10 x64
Athlon 64 FX-62 @ 3,18 GHz

2003 :


R11.5


R15 :
 

can feel the amd running through my blood seeing dat chip. so nice. i wanted the fx60 the 939 one but they are so expensive :'( such a beast of a cpu

[agent_x007]

I would love to test FX-60 in DirectX 12 (x64), but I can't
Rev. E6 of K8 architecture doesn't have necessary instructions (CompareExchange128/CMPXCHG16B).
FX-62 is the closest CPU to it

[lawrencejames]

[DildorTheDecent]

8 hours ago, lawrencejames said:

 

multicore run tho?