Post your Cinebench R20+15+R11.5+2003 Scores **Don't Read The OP PLZ**

[Jumper118]

34 minutes ago, maybethisnamewillwork said:

Yeah it actually seems to perform a bit better in aida64 cache & memory benchmark.
Also managed to slightly tighten some timings so now I'm running stable 10-12-11-28 1T. 

Yeah makes a difference.  I was running my ddr4 at 2t for a while and it's so slow. 

[Jumper118]

On 17/12/2016 at 11:28 PM, Dabombinable said:

Finally got my 4790K running better, turns out that adjusting the VRM to run at full phased, and the FIVR to run at performance made a massive difference-though I couldn't replicate the top score with multiple re-runs (4.8GHz 1 core, 4.7GHz 2-3 core, 4.6GHz 4 core).

Getting much better but like you say, you need better ram.  Maybe try picking up some half decent 2*2gb kit that's 1600c8.  Should be cheap because 2gb sticks of ddr3 aren't that useful. 

[Dabombinable]

11 minutes ago, Jumper118 said:

Getting much better but like you say, you need better ram.  Maybe try picking up some half decent 2*2gb kit that's 1600c8.  Should be cheap because 2gb sticks of ddr3 aren't that useful. 

Would any of these be good?

http://www.ebay.com.au/sch/i.html?_odkw=ddr3+1600&Number%20of%20Pins=240&Form%20Factor=DIMM&_sop=15&LH_BIN=1&_dcat=170083&_osacat=170083&_from=R40&_trksid=p2045573.m570.l1313.TR0.TRC0.H0.Xddr3+1600+cl8.TRS0&_nkw=ddr3+1600+cl8&_sacat=170083

 

Edit: Or these (CL11, 2133MHz)? https://www.computeralliance.com.au/8gb-ddr3-g.skill-f3-17000cl11d-8gbxl-(2x4g)-2133mhz-ram

[Mr.Meerkat]

Why the hell not submit on this topic eh?  

 

Now tiem to go back to 4.5GHz...when I can be bothered booting back into Bios again...

[Jumper118]

2 hours ago, Dabombinable said:

Would any of these be good?

http://www.ebay.com.au/sch/i.html?_odkw=ddr3+1600&Number%20of%20Pins=240&Form%20Factor=DIMM&_sop=15&LH_BIN=1&_dcat=170083&_osacat=170083&_from=R40&_trksid=p2045573.m570.l1313.TR0.TRC0.H0.Xddr3+1600+cl8.TRS0&_nkw=ddr3+1600+cl8&_sacat=170083

 

Edit: Or these (CL11, 2133MHz)? https://www.computeralliance.com.au/8gb-ddr3-g.skill-f3-17000cl11d-8gbxl-(2x4g)-2133mhz-ram

No.  You need a 2*2gb kit for $35-40 aussi. Dealz must be had.  Fond some used ram.  Looking at g. Skill but also less popular ram brands as well. Just type them into ebay and go on low to high. 

[DildorTheDecent]

10 hours ago, iHardware Shelden said:

 

That the best it does? 

[iHardware Shelden]

22 minutes ago, DildorTheDecent said:

That the best it does? 

Not my system or I'd push it more, from what I can tell it's pretty good but just built it for a friend and did a slight overclock  

[done12many2]

32 minutes ago, iHardware Shelden said:

Not my system or I'd push it more, from what I can tell it's pretty good but just built it for a friend and did a slight overclock  

Seems pretty nice to me.  

 

 

55 minutes ago, DildorTheDecent said:

That the best it does? 

What's the best you got out of your 5820k?  Never mind. I found it.  I'm readjusting my per core overclock and I'm 6 cores at the moment. 

[0ld_Chicken]

Called in to work today (sick) so I decided to bench for a bit.  I've bested my last R15 submission (1007pts) by 14 for a total of 1024.  I only spent all morning doing it.  

The highest cinebench temps i've monitored are 64°c so I'm kinda tempted to take the vcore higher and see if I can squeeze 5.1 now that I am running my cpu naked.  What do you guys think?

 

 

 

 

 

also did a run after loading cpu-z and HWinfo to show temps and still got 1024.

Spoiler

 

[done12many2]

9 minutes ago, 0ld_Chicken said:

Called in to work today (sick) so I decided to bench for a bit.  I've bested my last R15 submission (1007pts) by 14 for a total of 1024.  I only spent all morning doing it.  

The highest cinebench temps i've monitored are 64°c so I'm kinda tempted to take the vcore higher and see if I can squeeze 5.1 now that I am running my cpu naked.  What do you guys think?

 

also did a run after loading cpu-z and HWinfo to show temps and still got 1024.

 

 

Damn nice single-threaded for sure!!

 

There's a glitch in R15 when you run subsequent tests, it'll keep posting the same score from previous tests.  Not every time, but it happens a lot.

[0ld_Chicken]

2 minutes ago, done12many2 said:

 

Damn nice single-threaded for sure!!

Thanks!  I only gained 1pt on single thread, compared to the 14 on multicore but I guess that could add up with rounding.  Plus I only ran single core once, pts/GHz went up 3.5 i think though to 204.9

[Jumper118]

7 minutes ago, 0ld_Chicken said:

Thanks!  I only gained 1pt on single thread, compared to the 14 on multicore but I guess that could add up with rounding.  Plus I only ran single core once, pts/GHz went up 3.5 i think though to 204.9

memory trfc. try get that down nearer 100. start at 200 and work you way down. 

[0ld_Chicken]

34 minutes ago, Jumper118 said:

memory trfc. try get that down nearer 100. start at 200 and work you way down. 

phew, start at 200?  more like, can't boot under 215 haha.  225 was lowest I could get through Cinebench.  I tried dropping freq down to 2178 just to see if 200 could boot and still crashed. 

 

Know of any good ddr3 OC guides?  especially tertiary?  I've looked but can't find much that is helpful

 

It did get things up to 1026 though

 

I have been closing everything down that I can, including explorer and setting Cinebench priority to realtime, with only a bit of the window actually visable. 

 

[Jumper118]

9 minutes ago, 0ld_Chicken said:

phew, start at 200?  more like, can't boot under 215 haha.  225 was lowest I could get through Cinebench.  I tried dropping freq down to 2178 just to see if 200 could boot and still crashed. 

 

Know of any good ddr3 OC guides?  especially tertiary?  I've looked but can't find much that is helpful

 

It did get things up to 1026 though

 

 

I have been closing everything down that I can, including explorer and setting Cinebench priority to realtime, with only a bit of the window actually visable. 

 

i can help you but i need to know what kit you have? 2x8gb? 

[done12many2]

15 minutes ago, 0ld_Chicken said:

Know of any good ddr3 OC guides?  especially tertiary?  I've looked but can't find much that is helpful

 

Old, but remains very applicable.

 

http://www.anandtech.com/show/3851/everything-you-always-wanted-to-know-about-sdram-memory-but-were-afraid-to-ask
 

[0ld_Chicken]

1 minute ago, Jumper118 said:

i can help you but i need to know what kit you have? 2x8gb? 

well that's probably part of the problem.  I'm using a 4x4gb Klevv NEO 2133 10-12-12-31, would I be better off to remove 2 dimms temporarily?  I thought about doing that but they're in there pretty tight between GPU backplate and top fans.  If it'd be worth it I'll get it done though

[Jumper118]

11 minutes ago, 0ld_Chicken said:

well that's probably part of the problem.  I'm using a 4x4gb Klevv NEO 2133 10-12-12-31, would I be better off to remove 2 dimms temporarily?  I thought about doing that but they're in there pretty tight between GPU backplate and top fans.  If it'd be worth it I'll get it done though

ideally you would test them one at a time and use the best 2, but aint nobody got time for that  theya re probably the lowest samsung bin i hope. 9-11-11-28 1T would be good. i think your trfc is quite high but still miles better than it was. if it is samsung you can go all the way to 2.1v on them, but if they arent then that would be a bad idea!. to play it safe i would try get it to 1.85v and drop on timing at a time. try 10-12-11-31 1T, then 10-11-12-31 1T, then 9-12-12-31 1T, 9-11-11-31 1T then drop the 31 to 28. then we can go from there. 

 

you could try them at 1.65v at first if you want and if you can it would help to take 2 dimms out. 

[0ld_Chicken]

5 minutes ago, Jumper118 said:

ideally you would test them one at a time and use the best 2, but aint nobody got time for that  theya re probably the lowest samsung bin i hope. 9-11-11-28 1T would be good. i think your trfc is quite high but still miles better than it was. if it is samsung you can go all the way to 2.1v on them, but if they arent then that would be a bad idea!. to play it safe i would try get it to 1.85v and drop on timing at a time. try 10-12-11-31 1T, then 10-11-12-31 1T, then 9-12-12-31 1T, 9-11-11-31 1T then drop the 31 to 28. then we can go from there. 

 

you could try them at 1.65v at first if you want and if you can it would help to take 2 dimms out. 

SK group owns Klevv and Hynix iirc so I'm almost certain that they'd be Hynix but I could be wrong.  Running 1.725v on dram right now, but I'll take two dimm out and take the rest up to 1.85 and try some of these timings.  They've got 2200rpm of Vardar goodness directly on them so I hope they'll be alright 

 

Oh I've also got a 1x8gb Gskill 2400 CL11-13-13-31 @ 1.65v laying around if that might have more potential

23 minutes ago, done12many2 said:

Old, but remains very applicable.

 

http://www.anandtech.com/show/3851/everything-you-always-wanted-to-know-about-sdram-memory-but-were-afraid-to-ask

Great read!  I think I'm going to have to try again when I'm less feverish though, that is some deep knowledge there for a simple mind like my own!

 

[Jumper118]

20 minutes ago, 0ld_Chicken said:

SK group owns Klevv and Hynix iirc so I'm almost certain that they'd be Hynix but I could be wrong.  Running 1.725v on dram right now, but I'll take two dimm out and take the rest up to 1.85 and try some of these timings.  They've got 2200rpm of Vardar goodness directly on them so I hope they'll be alright 

 

Oh I've also got a 1x8gb Gskill 2400 CL11-13-13-31 @ 1.65v laying around if that might have more potential

Great read!  I think I'm going to have to try again when I'm less feverish though, that is some deep knowledge there for a simple mind like my own!

 

if they are hynix you are screwed. thats explains why the trfc wouldn't do below 200 . you are best off running them on ln2 at 3000mhz mhz cl150000 

[done12many2]

@Jumper118  I hope for your sake that this is way off.  

 

http://wccftech.com/amd-ryzen-zen-cpu-benchmarks-leak/

 

 

 

[Jumper118]

1 minute ago, done12many2 said:

@Jumper118  I hope for your sake that this is way off.  

 

http://wccftech.com/amd-ryzen-zen-cpu-benchmarks-leak/

 

 

 

 

yeah i saw that in the other thread. i hope thats the 6c12t version and not the 8  

[done12many2]

4 minutes ago, Jumper118 said:

yeah i saw that in the other thread. i hope thats the 6c12t version and not the 8  

 

Grain of salt of course, but it's described as the 8c/16t bud.

[Jumper118]

1 minute ago, done12many2 said:

 

Grain of salt of course, but it's described as the 8c/16t bud.

i wonder if they had steam tweak+ 2133mhz c21 ram and 3.4ghz and normal  otherwise rip amd.

[0ld_Chicken]

12 minutes ago, Jumper118 said:

if they are hynix you are screwed. thats explains why the trfc wouldn't do below 200 . you are best off running them on ln2 at 3000mhz mhz cl150000 

haha thats cool, I've been trying lower timings with only 2 dimms and been scoring between 1009-1017    I'll settle for 1026pts for now.  Thanks for your help though, it's much appreciated!  

I'm sure I'll be back around soon

[done12many2]

2 minutes ago, Jumper118 said:

i wonder if they had steam tweak+ 2133mhz c21 ram and 3.4ghz and normal  otherwise rip amd.

 

As usual, I'm sure that the truth lies somewhere in the middle of AMD's presentation and the leaks that are starting to come out.