Post your Cinebench R20+15+R11.5+2003 Scores **Don't Read The OP PLZ**

[Raudi_]

fx4100....... is worse than the fx4170. seem amd's binning is working

 this is off on the bay tomorrow and i've bought another one, which is hopefully better

 

also i've got a phenom ii x6 1055T to test tommorrow and a gigabyte 790x ud3p to oc and unlock the sempron with

If you were closer I would have no issue sending my Phenom 511 to you to see what could be done with it.

[TheLhent]

Refresh my score, and i know, the vcore, is too high, i reach 4.9 with that vcore, later i will refresh with 4.9 ghz.

 

3930k 4.7 Ghz, Memory 2400 Mhz

 

[Jumper118]

Refresh my score, and i know, the vcore, is too high, i reach 4.9 with that vcore, later i will refresh with 4.9 ghz.

 

3930k 4.7 Ghz, Memory 2400 Mhz

 

 

nice score, but those ram timings are terrible? what is the xmp speed and timings.

[Lays]

nice score, but those ram timings are terrible? what is the xmp speed and timings.

 

I could only do like 11-12-12-32 on my 2133 kit @ 2400  my dom plat kit was poo for OC'ing.

Hopefully my new DDR4 kit will be able to tighten timings a lot. Seen a few people on hwbot with my kit getting crazy timings like 12-13-12-15 and around there (stock is 15-15-15-35)

 

 

Speaking of which, once 5820k goes on sale again on amazon I will start binning, I've got the mobo & RAM showing up this week like Thurs/Fri.

[TheLhent]

nice score, but those ram timings are terrible? what is the xmp speed and timings.

Well, this kingston hyperx predator has two xmp profile, 2400 mhz with these timmings(11-13-13-30) and i guess a profile with 2100 mhz and i dont know the timming, is realy bad timmings for this memory?

[Jumper118]

Well, this kingston hyperx predator has two xmp profile, 2400 mhz with these timmings(11-13-13-30) and i guess a profile with 2100 mhz and i dont know the timming, is realy bad timmings for this memory?

well if you go into the bios and change them to from 11-13-13-30 2T to 11-11-11-30 1T that would be a good start also set the voltage of the ram to 1.65v 

[Lays]

well if you go into the bios and change them to from 11-13-13-30 2T to 11-11-11-30 1T that would be a good start also set the voltage of the ram to 1.65v 

 

 

Trying to cut a deal with the silicon lottery guy to see if I can get a 4.7 chip for less, $679 is a bit ridiculous lol. 

 

I'll ask him if I give him a shoutout and include him in my build-log, since it does have 45,000 views after-all.

 

Dunno where it would get me, but might as well try.

[Jumper118]

Trying to cut a deal with the silicon lottery guy to see if I can get a 4.7 chip for less, $679 is a bit ridiculous lol. 

 

I'll ask him if I give him a shoutout and include him in my build-log, since it does have 45,000 views after-all.

 

Dunno where it would get me, but might as well try.

it is worth a try.  

[FuzzyYellow]

i think i'm going to try to push to 4.7ghz on my G3258. what's the MAX safe voltage i can pump w/ air cooling?

[Jumper118]

i think i'm going to try to push to 4.7ghz on my G3258. what's the MAX safe voltage i can pump w/ air cooling?

for benching, you can go to 1.5v fine, you might find it doesn't scale very well though. i put 1.6v through mine on air

[FuzzyYellow]

for benching, you can go to 1.5v fine, you might find it doesn't scale very well though. i put 1.6v through mine on air

ok, i tried 1.35, but wasn't sure if i should go further than that...

[Jumper118]

ok, i tried 1.35, but wasn't sure if i should go further than that...

1.35v is ok for daily use, but you wont want to run it at 1.5+v for too long. its best just to get the score take the screeshot and then, boot back in at normal speed to upload and submit your score.

[TheLhent]

Jumper, i tried to change the timing of the memory, but, didn't work, some ideas?

[FuzzyYellow]

1.35v is ok for daily use, but you wont want to run it at 1.5+v for too long. its best just to get the score take the screeshot and then, boot back in at normal speed to upload and submit your score.

well, my mobo hard locks me at 1.4v, and that's not quite enough. it boots, but crashes when i run the bench. too bad... 

[Jumper118]

Jumper, i tried to change the timing of the memory, but, didn't work, some ideas?

ok maybe they were a bit too tight. try 11-12-12-30 2T to start with.

well, my mobo hard locks me at 1.4v, and that's not quite enough. it boots, but crashes when i run the bench. too bad... 

i didn't see you only had a h81 board. 1.5v might not have been a great idea anyway

[Raudi_]

well, my mobo hard locks me at 1.4v, and that's not quite enough. it boots, but crashes when i run the bench. too bad... 

I took me 1.52v for 4.82 for benching on a MSI Z87 XPower with a G3258

[TheLhent]

ok maybe they were a bit too tight. try 11-12-12-30 2T to start with.

i didn't see you only had a h81 board. 1.5v might not have been a great idea anyway

I'm coming into a conclusion, or my ram isn't good with less timing, or the problem is with me changing, 11-12-12-30-2T works until i get the desktop area, after that, error and reboot...

[Jumper118]

I'm coming into a conclusion, or my ram isn't good with less timing, or the problem is with me changing, 11-12-12-30-2T works until i get the desktop area, after that, error and reboot...

well at least it booted. that is good 11-13-12-30 2T? 

[TheLhent]

well at least it booted. that is good 11-13-12-30 2T? 

Well, with 11-13-12-30-2T, until now, its ok. With this small change in professional programs, will have difference? Because, with bench, will be tinny i think.

 

[Jumper118]

Well, with 11-13-12-30-2T, until now, its ok. With this small change in professional programs, will have difference? Because, with bench, will be tinny i think.

 

 

it will be a very small difference, but a difference no the less. try 11-13-12-30 1T now. also run cinebench again, you need 2cb more to get 1200

[Lays]

@Jumper118 the ram kit I bought went down $20 after buying it, newegg gave me a gift card for the difference.

 

[harrynowl]

I have a 10% off voucher for electronics on eBay... I feel an i5 coming in soon

[Jumper118]

I have a 10% off voucher for electronics on eBay... I feel an i5 coming in soon

epic! i hope you get a really good one

@Jumper118 the ram kit I bought went down $20 after buying it, newegg gave me a gift card for the difference.

 

that is good of them, most places wouldn't do that

[Lays]

 

epic! i hope you get a really good one

that is good of them, most places wouldn't do that

 

 

 

They had their "iron egg guarantee" thing on it, so it's in their policy ya kno.

[Jumper118]

They had their "iron egg guarantee" thing on it, so it's in their policy ya kno.

fair enough. that sounds like a good policy to me!