TVwazhere

Hey ummm guys what do you do when the gas pump has a cylinder 4 misfire? 
 

All I had time to do today was splice the tap into the wire.

Depinned the terminal, cut about 3-4mm insulation off, split the strands, stuck the other wire through and wrapped it, slid a solder shrink on it, heated it at either end to seal it, hested the middle to solder it, cooled with wet fingers, reassembled. Should last a couple decades. Probably had room for the solder iron and good lead solder but this was faster and easier.

God https://stats.foldingathome.org/project/18215 this is hammering my cards... nice PPD though 

Sorry I'm late guys, but I finally built my new PC with my 408-
I missed it!?!?!?!?! FUUUUUUUUUCK
Well at least I can still comment about the eve-

Sorry I'm late guys, but I finally built my new PC with my 408-
I missed it!?!?!?!?! FUUUUUUUUUCK
Well at least I can still comment about the eve-

Sorry I'm late guys, but I finally built my new PC with my 408-
I missed it!?!?!?!?! FUUUUUUUUUCK
Well at least I can still comment about the eve-

@Mxyzptlk @miker07 you guys are actual mosnters, nearly getting a plat badge in a week

 
Also, It's weird that I'm relieved that I barely missed the prize by 1 randomly drawn number, where as normally I'd be gasping at how close I was. 

 
But the next sprint? I'll be ready

Those are there because Bruce, our Shark branded robot vacuum, couldnt fit under the coffee table (by like 1/2" or 12mm) so i 3D printed those to raise it up just a little bit.

Those are there because Bruce, our Shark branded robot vacuum, couldnt fit under the coffee table (by like 1/2" or 12mm) so i 3D printed those to raise it up just a little bit.

No I have a goth GF

Those are there because Bruce, our Shark branded robot vacuum, couldnt fit under the coffee table (by like 1/2" or 12mm) so i 3D printed those to raise it up just a little bit.

Those are there because Bruce, our Shark branded robot vacuum, couldnt fit under the coffee table (by like 1/2" or 12mm) so i 3D printed those to raise it up just a little bit.

Those are there because Bruce, our Shark branded robot vacuum, couldnt fit under the coffee table (by like 1/2" or 12mm) so i 3D printed those to raise it up just a little bit.

Sorry I'm late guys, but I finally built my new PC with my 408-
I missed it!?!?!?!?! FUUUUUUUUUCK
Well at least I can still comment about the eve-

@Mxyzptlk @miker07 you guys are actual mosnters, nearly getting a plat badge in a week

 
Also, It's weird that I'm relieved that I barely missed the prize by 1 randomly drawn number, where as normally I'd be gasping at how close I was. 

 
But the next sprint? I'll be ready

I forgot the solder splices I needed at home. I was pissed. Got the right wire, only on with ignition and doesn't drop out when cranking, comes from a dumb relay switched 15A fuse.

Those are there because Bruce, our Shark branded robot vacuum, couldnt fit under the coffee table (by like 1/2" or 12mm) so i 3D printed those to raise it up just a little bit.

Well happy belated birthday to you!

No I have a goth GF

Sorry I'm late guys, but I finally built my new PC with my 408-
I missed it!?!?!?!?! FUUUUUUUUUCK
Well at least I can still comment about the eve-

Well happy belated birthday to you!

No I have a goth GF

Yeah, I'm fine. Why do you ask?
 
 

So I won something on an event for someone else's Birthday, on my own Birthday.

Only me that find that amusing?

Questions that literally keep Spotty up at night

Kinda explains why it seems you never sleep