Posted October 11, 2017 The title says it all. I have a Z600 case and motherboard. I want to build a water cooling system into it, but only if it will work as well as, or better than the base air coolers. My question is, will a 60mm dual rad work to cool 2 x5650 CPUs? And if so, how would you make a loop to dissipate the heat evenly? Conventionalism says to just use 2 Y fittings and branch the pump output to both CPU blocks, then branch it back to the radiator. Link to comment Share on other sites More sharing options... Link to post Share on other sites More sharing options...
Posted October 11, 2017 Just my own experience, but I would avoid going parallel with water cooling. I had a situation once where there was a pocket of air in one of my gpu blocks which was creating flow resistance. This caused the water to be unevenly distributed to the other gpu block. Link to comment Share on other sites More sharing options... Link to post Share on other sites More sharing options...
Posted October 11, 2017 if you put these in a conventional loop you would create one 'cold' and one 'hot' chip. as the water from the first chip would heat up before it goes over the second chip. so a parallel setup seems to be the way to go. some manufacturers like bitspower make these handy block fittings which would make it look a lot nicer then Y splitters as mentioned above tough, parallel setups need to be filled properly, as bubbles of air mess with the flow. -Phoenix- -VouwFabriek- -SolidNAS- BlackMac Woody Clack Virtuality Lil'Lad Plot-Device Boerderij all your proteins are belong to us. Link to comment Share on other sites More sharing options... Link to post Share on other sites More sharing options...
Posted October 11, 2017 Author 1 hour ago, RollinLower said: if you put these in a conventional loop you would create one 'cold' and one 'hot' chip. as the water from the first chip would heat up before it goes over the second chip. so a parallel setup seems to be the way to go. some manufacturers like bitspower make these handy block fittings which would make it look a lot nicer then Y splitters as mentioned above tough, parallel setups need to be filled properly, as bubbles of air mess with the flow. So, as long as the pump has sufficient flow, it should not have cooling issues with splitting the system in this way. Correct? I was planning to use my 2 drive bays to house the pump/res combo. No real need for optical drives anymore. The setup is nearly for the "because I can" reason and to keep out as much heat inside as I can. No plans to overclock, or really to do much else other than to have "bolt-ons. I appreciate the info. Link to comment Share on other sites More sharing options... Link to post Share on other sites More sharing options...
Posted October 11, 2017 Author Oh, and I plan to just keep my gpu air cooled. Not enough room for that much water cooling. Lol Link to comment Share on other sites More sharing options... Link to post Share on other sites More sharing options...
Posted October 11, 2017 Not true unfortunatey. water moves around a pc so fast that the loop temperature goes up gradually as a whole. so you will not have a hot CPU and a cold cpu. (same logic as how loop order does not matter). The only consideration is the restriction of the CPU block. but I have seen dual CPU blocks in series with no problems Recent builds: Meshify C (Zero Tolerance!) & View 37 (Breathable Quad 2080Ti + 2990WX) Best documented PC coolants Older Builds Spoiler Full-custom loop builds: Meshify C (Full custom loop SLI), Ncase M1(8700K + 1080Ti Full custom loop) Obsidian 900D (1950X + Quad 1080Ti) & Fractal Define C (1080 in SLI) Air-cooled builds Air 740D (1920X + Quad 980Ti) & Fractal Define C (Version Air!) Link to comment Share on other sites More sharing options... Link to post Share on other sites More sharing options...
Posted October 11, 2017 Two 95w tdp cpus with a Dual 60mm rad id say no. Cool one cpu MAYBE my guess is you would have to have fans full speed. If pure cooling power is the goal id say a a 280 rad would be what your looking for. Dual 140 Or a dual 120 (240) thats slightly thicker (for more water volume) A single 480 tho would allow you to run the system silent. Link to comment Share on other sites More sharing options... Link to post Share on other sites More sharing options...
Posted October 11, 2017 Author 1 hour ago, JDMFTW said: Two 95w tdp cpus with a Dual 60mm rad id say no. Cool one cpu MAYBE my guess is you would have to have fans full speed. If pure cooling power is the goal id say a a 280 rad would be what your looking for. Dual 140 Or a dual 120 (240) thats slightly thicker (for more water volume) A single 480 tho would allow you to run the system silent. As much as I would love to be able to fit a rad that huge, there is simply not enough room in the case. At least without cutting it up. I do have 2 astek AIO Intel water coolers. But again, the really won't fit in my case. 1 hour ago, For Science! said: Not true unfortunatey. water moves around a pc so fast that the loop temperature goes up gradually as a whole. so you will not have a hot CPU and a cold cpu. (same logic as how loop order does not matter). The only consideration is the restriction of the CPU block. but I have seen dual CPU blocks in series with no problems But, which style would work better? Having the two blocks in series or parallel? Link to comment Share on other sites More sharing options... Link to post Share on other sites More sharing options...
Posted October 11, 2017 2 minutes ago, Tylerspyler said: As much as I would love to be able to fit a rad that huge, there is simply not enough room in the case. At least without cutting it up. I do have 2 astek AIO Intel water coolers. But again, the really won't fit in my case. But, which style would work better? Having the two blocks in series or parallel? Between parallel and series, you are unlikely to observe any differences. However if one was to get slightly more clogged than the other for example, then a parallel configuration would have more severe consequences than in series. So in terms of a fail-safe, series would be the better option. I think 120mm of rad space per cpu that is 60 mm, especially if its a non-overclocked CPU, would be sufficient to keep things under reasonable control. Just get a pump that doesn't dump too much heat into the loop Recent builds: Meshify C (Zero Tolerance!) & View 37 (Breathable Quad 2080Ti + 2990WX) Best documented PC coolants Older Builds Spoiler Full-custom loop builds: Meshify C (Full custom loop SLI), Ncase M1(8700K + 1080Ti Full custom loop) Obsidian 900D (1950X + Quad 1080Ti) & Fractal Define C (1080 in SLI) Air-cooled builds Air 740D (1920X + Quad 980Ti) & Fractal Define C (Version Air!) Link to comment Share on other sites More sharing options... Link to post Share on other sites More sharing options...
Posted October 11, 2017 9 minutes ago, Tylerspyler said: -snip- Here are some examples of my google-fu "dual xeon water" Recent builds: Meshify C (Zero Tolerance!) & View 37 (Breathable Quad 2080Ti + 2990WX) Best documented PC coolants Older Builds Spoiler Full-custom loop builds: Meshify C (Full custom loop SLI), Ncase M1(8700K + 1080Ti Full custom loop) Obsidian 900D (1950X + Quad 1080Ti) & Fractal Define C (1080 in SLI) Air-cooled builds Air 740D (1920X + Quad 980Ti) & Fractal Define C (Version Air!) Link to comment Share on other sites More sharing options... Link to post Share on other sites More sharing options...
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now