Jump to content

Lian Li 011 MOBO fitment issue

NuclearMonkey
By NuclearMonkey
in Cases and Mods
 Share
Posted

I have a BNIB Lian Li 011-D Razer case that I'm attempting to transfer my PC into. 
My motherboard is an ASUS TUF Z390 Gaming Plus. 
The IO shield is inserted correctly. 
If I line the MOBO up with the pre installed stand offs it all seems to sit about 1-2mm away from the back of the case.
My GPU is a Zotac 1070 Amp edition. The back end clicks into the lever but the front doesn't seem to push all the way in and the bracket doesn't line up with the holes to be secured in place. 

If i put my sound card or WiFi card and push them into the slot then try and screw them in place it pulls them out of the MOBO.
I've attempted to loosen the screws off slightly that hold the MOBO in place to allow it to slide a bit but that doesn't help. 
If I take all the screws out and fit the cards into their slots and screw them to the case the MOBO isn't aligned with the stand offs.

Am I going to need a new MOBO? Or is my brand new case fubar?

Any help would be appreciated.

Link to comment
Share on other sites
Link to post
Share on other sites
Posted
19 hours ago, NuclearMonkey said:

I have a BNIB Lian Li 011-D Razer case that I'm attempting to transfer my PC into. 
My motherboard is an ASUS TUF Z390 Gaming Plus. 
The IO shield is inserted correctly. 
If I line the MOBO up with the pre installed stand offs it all seems to sit about 1-2mm away from the back of the case.
My GPU is a Zotac 1070 Amp edition. The back end clicks into the lever but the front doesn't seem to push all the way in and the bracket doesn't line up with the holes to be secured in place. 

If i put my sound card or WiFi card and push them into the slot then try and screw them in place it pulls them out of the MOBO.
I've attempted to loosen the screws off slightly that hold the MOBO in place to allow it to slide a bit but that doesn't help. 
If I take all the screws out and fit the cards into their slots and screw them to the case the MOBO isn't aligned with the stand offs.

Am I going to need a new MOBO? Or is my brand new case fubar?

Any help would be appreciated.

9 hours ago, NuclearMonkey said:

 

Spoiler

20200917_072312.jpg

 

My best guess is that the case is palatially bent, those screw holes got the PCI-E bracket should line up pretty much perfectly. How easy is it to take off/put on the tempered glass side panel?

"Put as much effort into your question as you'd expect someone to give in an answer"- @Princess Luna

Make sure to Quote posts or tag the person with @[username] so they know you responded to them!

 RGB Build Post 2019 --- Rainbow 🦆 2020 --- Velka 5 V2.0 Build 2021

Purple Build Post ---  Blue Build Post --- Blue Build Post 2018 --- Project ITNOS

CPU i7-4790k    Motherboard Gigabyte Z97N-WIFI    RAM G.Skill Sniper DDR3 1866mhz    GPU EVGA GTX1080Ti FTW3    Case Corsair 380T   

Storage Samsung EVO 250GB, Samsung EVO 1TB, WD Black 3TB, WD Black 5TB    PSU Corsair CX750M    Cooling Cryorig H7 with NF-A12x25

Link to comment
Share on other sites
Link to post
Share on other sites
Posted

Are all the motherboard standoffs under the board on that edge?  It might be the board flexing down? 

Link to comment
Share on other sites
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing Cases and Mods

×