Jump to content

Solid back panel for Enthoo Evolv ATX TG?

SUPER_MOOSE93
By SUPER_MOOSE93
in Cases and Mods
 Share
Posted

I am planning a build and finding a nice case is turning out to be a struggle. I have a tempered glass version of the enthoo evolv that im currently not using, and while i do like the look of the case, i dont like seeing the rear side and the mess of cables. Does anyone make a solid back panel that uses the same screw mounting? or how much do you think it would cost to get a panel made?

Link to comment
https://linustechtips.com/topic/1265559-solid-back-panel-for-enthoo-evolv-atx-tg/
Share on other sites
Link to post
Share on other sites
Posted

Unfortunatley getting a Non TG solid rear panel isnt an option since it uses different mounting

Evolv-ATX-11.jpg.cdecd0a0a29321e1c362a5b3edc1d7bb.jpg100031493_Evolv-ATX-11(1).jpg.00374911a83787297282d4954e2fa87a.jpg

Since you have the TG panel, it should be easy enough to make a template and then have a rear panel cut out or 3D Printed for you. Where you would go to get that done I'm not sure, hopefully a local fabrication shop would have the materials you need (thinner than 1/16" Sheet metal perhaps?)

"Put as much effort into your question as you'd expect someone to give in an answer"- @Princess Luna

Make sure to Quote posts or tag the person with @[username] so they know you responded to them!

 RGB Build Post 2019 --- Rainbow 🦆 2020 --- Velka 5 V2.0 Build 2021

Purple Build Post ---  Blue Build Post --- Blue Build Post 2018 --- Project ITNOS

CPU AMD R7 7800X3D    Motherboard Asrock B650E Taichi Lite    RAM Corsair Vengeance RGB 32GB 5200mhz    GPU ASUS RTX4080 STRIX 

Case Fractal Torrent   Storage Samsung 980Pro 2TB, Crucial P3 Plus 4TB x2,     PSU Corsair RM1000x    Cooling Deepcool AK620

Link to post
Share on other sites
Posted
  • Author
12 hours ago, Blue4130 said:

1/16" would be very floppy/bendy. I had a side panel made for my case and used 1/8" stainless steel. Even that bows out quite easily. 

The face and top plate are 3mm aluminium. i think the hardest part will be getting the finish to match

Link to post
Share on other sites
Posted
On 11/6/2020 at 5:02 PM, Blue4130 said:

1/16" would be very floppy/bendy. I had a side panel made for my case and used 1/8" stainless steel. Even that bows out quite easily. 

1/8"? I'd like to see that because I'm highly doubtful; that's VERY thick stuff, quite heavy and not easy to bend. Most panels are under 1/16" (2mm)

"Put as much effort into your question as you'd expect someone to give in an answer"- @Princess Luna

Make sure to Quote posts or tag the person with @[username] so they know you responded to them!

 RGB Build Post 2019 --- Rainbow 🦆 2020 --- Velka 5 V2.0 Build 2021

Purple Build Post ---  Blue Build Post --- Blue Build Post 2018 --- Project ITNOS

CPU AMD R7 7800X3D    Motherboard Asrock B650E Taichi Lite    RAM Corsair Vengeance RGB 32GB 5200mhz    GPU ASUS RTX4080 STRIX 

Case Fractal Torrent   Storage Samsung 980Pro 2TB, Crucial P3 Plus 4TB x2,     PSU Corsair RM1000x    Cooling Deepcool AK620

Link to post
Share on other sites
Posted

You could just get some matte window film and put it on the inside or outside of the panel. Hides the cables, looks decent and if it's on the inside you can be all about that extreme tempered glass that you can no longer see through look :p.

Link to post
Share on other sites
Posted
1 hour ago, TVwazhere said:

1/8"? I'd like to see that because I'm highly doubtful; that's VERY thick stuff, quite heavy and not easy to bend. Most panels are under 1/16" (2mm)

So it's not true 1/8th inch because I am in metric land. It's 3mm. Weight was not a concern. 

IMG_20181103_141013.jpg

IMG_20181103_140954.jpg

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing Cases and Mods

×