Please help me

[Tacos16x20]

Just finished putting together my PC, when I turn it on, the RGB for the Motherboard and RAM light up, the power supply fan spins up for about 4-6 seconds and then stops, I'm getting no display to my monitor, and no beeping(someone asked about my motherboard speaker, I said I didn't know anything about it).

 

I'll post the parts I'm using, and they are a bit strange, our company ordered the wrong parts or too much of something and we were just told to take what we want. 

https://pcpartpicker.com/user/Tacos16x20/saved/#view=ptFQD3

I'm using Corsair Vengeance Led 4 x 8gb 3200MHz for RAM

[Eighjan]

Just connect the drive you want as boot, first... then add the rest later.

[Tacos16x20]

Just now, Eighjan said:

Just connect the drive you want as boot, first... then add the rest later.

But shouldn't any of the fans be spinning? Even the CPU fan? Because not a single fan is spinning

[Eighjan]

1 minute ago, Tacos16x20 said:

But shouldn't any of the fans be spinning? Even the CPU fan? Because not a single fan is spinning

Can the 'board get into the BIOS?

[Tacos16x20]

Just now, Eighjan said:

Can the 'board get into the BIOS?

When i turn it on and connect display, i dont get anything, only black screens

[Fasauceome]

9 minutes ago, Tacos16x20 said:

someone asked about my motherboard speaker, I said I didn't know anything about it

It usually comes in the box as a separate little item

[Tacos16x20]

2 minutes ago, Fasauceome said:

It usually comes in the box as a separate little item

Didn't see one of those during the entire build

[Eighjan]

2 minutes ago, Tacos16x20 said:

When i turn it on and connect display, i dont get anything, only black screens

Did you test the 'board, on the box, before you built into the case?

[Eighjan]

4 minutes ago, Fasauceome said:

It usually comes in the box as a separate little item

These aren't as common as they used to be, these days... esp. with the rise in populairty of code displays.

[Tacos16x20]

1 minute ago, Eighjan said:

Did you test the 'board, on the box, before you built into the case?

I probably should have done that, i got a little ahead of myself watching a build guide

[Eighjan]

Just now, Tacos16x20 said:

I probably should have done that, i got a little ahead of myself watching a build guide

Oh dear... strip the build & test the core spec., first.

[TekSupport]

Just now, Tacos16x20 said:

I probably should have done that, i got a little ahead of myself watching a build guide

First I would read this Post, and try the steps it recommends.

 

[Tacos16x20]

Just now, Eighjan said:

Oh dear... strip the build & test the core spec., first.

and i was watching a linus build guide too... give me like 20 minutes and ill come back with what i get

[Eighjan]

As "The Master" always says - "do as I SAY, not as I DO."

[Eighjan]

2 minutes ago, TekSupport said:

First I would read this Post, and try the steps it recommends.

 

Dat flowchart, though...  

[boggy77]

try with just two sticks of ram, in slots 2 and 4 first. 

[Tacos16x20]

17 minutes ago, Eighjan said:

Oh dear... strip the build & test the core spec., first.

Not sure if this is common knowledge or not, but do i need to have a hard drive plugged in when i take the mobo out and start it up?

 

[Eighjan]

Just now, Tacos16x20 said:

Not sure if this is common knowledge or not, but do i need to have a hard drive plugged in when i take the mobo out and start it up?

 

Not to get to the BIOS; no...

[Tacos16x20]

17 minutes ago, Eighjan said:

Not to get to the BIOS; no...

Alright, i have the motherboard out, sitting on the mobo box, the cpu 8 pin cable plugged in, and the 24 pin plugged in, monitor plugged into the motherboard as well, using display port, is there anything else i need to do before i turn the power supply on?

[Eighjan]

1 minute ago, Tacos16x20 said:

Alright, i have the motherboard out, sitting on the mobo box, the cpu 8 pin cable plugged in, and the 24 pin plugged in, monitor plugged into the motherboard as well, using display port, is there anything else i need to do before i turn the power supply on?

Graphics card - 3600 has no iGPU.

[Tacos16x20]

2 minutes ago, Eighjan said:

Graphics card - 3600 has no iGPU.

Was used to my old computer having an APU so i didnt need a GPU for a while, just put the 1060 in the motherboard, now all i do is flip the power supply switch, right?

 

[Eighjan]

Yup... then get ready to 'mash' Delete - on keyboard - to get to BIOS

[Tacos16x20]

4 minutes ago, Eighjan said:

Yup... then get ready to 'mash' Delete - on keyboard - to get to BIOS

Turned the Power supply on, the rgb on the mobo lights up, the ram no longer lights up, none of the fans are spinning up (ie. cpu cooler, gpu, and psu), no display whatsoever either

No noise from the motherboard, no little red dot or anything anywhere either

Turned the power supply off after about 45 seconds because it didnt seem right

 

[Eighjan]

1 minute ago, Tacos16x20 said:

Turned the Power supply on, the rgb on the mobo lights up, the ram no longer lights up, none of the fans are spinning up (ie. cpu cooler, gpu, and psu), no display whatsoever either

No noise from the motherboard, no little red dot or anything anywhere either

Turned the power supply off after about 45 seconds because it didnt seem right

 

Is the CPU cooler fan connected?

Reseat two matched RAM sticks in slots 2 & 4 - away from the CPU.

Does the 1060 have it's power?

[Tacos16x20]

3 minutes ago, Eighjan said:

Is the CPU cooler fan connected?

Reseat two matched RAM sticks in slots 2 & 4 - away from the CPU.

Does the 1060 have it's power?

Fan is plugged into CPU_FAN
Changed the RAM slots so now its 2 and 4
And yes the GPU has its 6 pin plugged into it