New AIO computer wont display

[PolskyMurillo]

Hello

I need some help please

 

My Build

-------------------

Asus Maximus Hero 9

Intel i7700k

Asus 1060 GTX

Power supply TX850m

AIO NZXT Kraken m22

 

OK so I had my computer up and everything was running fine but the temps were at max 91 celsius when running cinebench r20

So i decided to change my kraken m22 to a kraken x72 (3 fan model)

Since i put the kraken x72,I cant get the pc to display.

 

Things  ive tried thus far

-changing to another confirmed working video card (same does not display anything)

-Remove ram

-Make sure no plastic is left on aio

-Reinstalled aio make sure that was not the issue

-Reset cmos

-Made sure krakan x72 works (feel the tubes do have running water)

-Rad is cold at the touch

-HDMI ports

-Display ports

-Another monitor

 

 

 

So im getting no where.

PC was working fine before aio switch

please help TY

 

 

[ahuckphin]

I would try re-installing the CPU. 

[Garett1]

Have you tried re seating your krakan? Make sure it is seated properly, and make sure your CPU is also seated properly. Sometimes when putting that on there you can accidentally move your CPU out of its slot just slightly and it wont boot.

[PolskyMurillo]

Yes sadly tried re seating the cpu

[Tristerin]

Couple things:

 

Mount pressure could be to tight, make sure your mobo isn't bending around the socket?

Did you plug in the CPU power cable back into the motherboard (EPS 12v) from the PSU?

[PolskyMurillo]

mobo is not bending and EPS 12v is plugged (both of them)

[For Science!]

27 minutes ago, PolskyMurillo said:

-

Have you tried the motherboard display outputs (maybe its sending it out through iGPU for some reason)

[For Science!]

2 minutes ago, PolskyMurillo said:

 

Also since you have a Q-code readout, let us know what it hangs on, if it is hanging on anything,

[PolskyMurillo]

I have tried mobo displays outputs and still nothing

Not sure what q code readouts are?

TY

[For Science!]

4 minutes ago, PolskyMurillo said:

I have tried mobo displays outputs and still nothing

Not sure what q code readouts are?

TY

There is an LED display on the top right of the motherboard, it should display either 2 characters (number + character). Leave you PC to POST for a while, and after the number/character stops flickering and changing, let us know what it stops on.

[For Science!]

While you're at it, you should post some photos of the PC, somebody may be able to spot something easily.

[PolskyMurillo]

So updates mobo code says CC and here are some pics

 

Usb pump cable goes to usb on mobo and 3 pin cable is on cpu fan on the mobo

Ty

[For Science!]

Could you just make sure both RAM sticks are seated properly? In the photo one looks slightly higher than the other. Also in the photo you are missing one of the retention screws of the cooler, what's going on there?

[For Science!]

Also try to hold the clear cmos button on the motherboard (on the rear i/o) while the system is powered off, and then try to see if that can help too.

[PolskyMurillo]

Hello i have cleared cmos and nothing

About the retention screw missing my bad i was sure i put it up in initial post my bad.

Yes my kit was missing one and i dyi it with a mobo peg.dont like it much hut the cooler is firm and not moving.

And about the ram i had not notice the cpu pumps are pushing it to the side

i will try foxing those things one by one

[PolskyMurillo]

Your hit in on the nail,my second ram become undone while installing aio.i did not even cosider second stick since i did not touch it but i did remove replut the first stick

[PolskyMurillo]

Ty all for the help