My system won't boot!

[YourComputerGeek]

Hi,

       I just built A whole new system, It boots up, but won't show a signal to my screen, I tried switching the RAM around, Checked power connections, etc. What else can I try to trouble shoot? 

[Squibbies18]

try using a different graphics card or display port of you can

7 minutes ago, YourComputerGeek said:

Hi,

       I just built A whole new system, It boots up, but won't show a signal to my screen, I tried switching the RAM around, Checked power connections, etc. What else can I try to trouble shoot? 

 

[kelvinhall05]

2 hours ago, YourComputerGeek said:

Hi,

       I just built A whole new system, It boots up, but won't show a signal to my screen, I tried switching the RAM around, Checked power connections, etc. What else can I try to trouble shoot? 

 

Specs? Make sure that your video cable is plugged into your GPU and not your motherboard.

[Inception9269]

2 minutes ago, kelvinhall05 said:

Specs? Make sure that your video cable is plugged into your GPU and not your motherboard.

was just about to say this

[YourComputerGeek]

5 minutes ago, kelvinhall05 said:

Specs? Make sure that your video cable is plugged into your GPU and not your motherboard.

i5 7500

MSI B150 Motherboard 

 

GTX 1070 FTW 

 

EVGA Supernova 650W power supply 

 

16GB of EVGA 2400MHZ RAM 

[kelvinhall05]

@YourComputerGeek Make sure the video cable is plugged into your GPU, not your motherboard. Are there any error codes/messages?

[YourComputerGeek]

1 minute ago, kelvinhall05 said:

@YourComputerGeek Make sure the video cable is plugged into your GPU, not your motherboard. Are there any error codes/messages?

No error codes on the motherboard, it's connected into GPU, still no signal 

[kelvinhall05]

2 hours ago, YourComputerGeek said:

No error codes on the motherboard, it's connected into GPU, still no signal 

Check all your power cables.

[YourComputerGeek]

3 minutes ago, kelvinhall05 said:

Check all your power cables.

Did that, Everything turns on, still no signal

[kelvinhall05]

2 hours ago, YourComputerGeek said:

Did that, Everything turns on, still no signal

At this point it sounds like a monitor issue. Did you check power and signal cables for both?

[YourComputerGeek]

19 minutes ago, kelvinhall05 said:

At this point it sounds like a monitor issue. Did you check power and signal cables for both?

I will check that

[YourComputerGeek]

43 minutes ago, kelvinhall05 said:

At this point it sounds like a monitor issue. Did you check power and signal cables for both?

Still nothing, I hooked up my brand new monitor 

[xdeathshot20]

3 minutes ago, YourComputerGeek said:

My system starts up fine, but no signal from GPU or motherboard, I tried different monitors, different cables, switching the ram around, nothing has worked. I don't get what else I can do! Any ideas? 

are there any error lights on the motherboard?  are the fans spinning on the gpu?  try removing the gpu and running on intergrated graphics

[imreloadin]

3 minutes ago, YourComputerGeek said:

My system starts up fine, but no signal from GPU or motherboard, I tried different monitors, different cables, switching the ram around, nothing has worked. I don't get what else I can do! Any ideas? 

So you don't even see the BIOS/UEFI correct?

[YourComputerGeek]

14 minutes ago, xdeathshot20 said:

are there any error lights on the motherboard?  are the fans spinning on the gpu?  try removing the gpu and running on intergrated graphics

No error lights are on, GPU is on and spinning, tried the motherboard graphics, nothing 

[YourComputerGeek]

15 minutes ago, imreloadin said:

So you don't even see the BIOS/UEFI correct?

Yup, I see nothing 

[kelvinhall05]

11 hours ago, YourComputerGeek said:

Still nothing, I hooked up my brand new monitor 

Try an old monitor if you can.

[YourComputerGeek]

On 2/5/2017 at 5:40 AM, kelvinhall05 said:

Try an old monitor if you can.

I think it's an BIOS update that's needed, everything works except for video, because I went with the new 7500, the motherboard I have never was updated I think, any idea how to load a new one onto it?