HELP!!!!! Ram not fitting

[SarfM786]

So i got a new PC and im trying to put the ram in the motherboard but it doesnt go all the way in and I put alot of force on it too It isnt going in all the way I dont want to damage my ram by putting even more force 

 

http://ca.pcpartpicker.com/list/ZqszPs

[potatoproduction]

Did you try to turn it around?

I only goes in on on one side

[Oswin]

is is not the other way around?

[EunSoo]

You need to link the perma link for you pcpartpicker build. That link just sends me to my own list

[SarfM786]

No its the correct way im 100% sure I already built many computers in the past

[Alexcalibur]

Make sure that little notch on the motherboard is aligned with the slot on the sticks. Also the PCP list you gave doesn't send us anywhere.

[toasty6776]

there's a notch in the DIMM and a corresponding notch in the socket. These have to line up

[SarfM786]

1 minute ago, SCGazelle said:

You need to link the perma link for you pcpartpicker build. That link just sends me to my own list

http://ca.pcpartpicker.com/list/ZqszPs

[Alexcalibur]

Did you buy something like DDR3 when you need DDR4?

[potatoproduction]

1 minute ago, IskanderEXC said:

Did you buy something like DDR3 when you need DDR4?

That wouldnt change how the ram goes in the comp just wouldn't start

[ImperialSteele]

Did you pull back the retention clip?

[FloRolf]

Just now, IskanderEXC said:

Did you buy something like DDR3 when you need DDR4?

Isn't dual Channel DDR2 the same as DDR4?

[MadG4mer]

You need to use some serious force when playing the RAM. The motherboard normally bends little bit if you dont have something under it.

[EunSoo]

1 minute ago, Sarfaraz said:

http://ca.pcpartpicker.com/list/ZqszPs

 

1 minute ago, IskanderEXC said:

Did you buy something like DDR3 when you need DDR4?

The RAM should be compatible. Both the MoBo and the RAM are DDR4. Make sure that you are putting it in the right orientation. Also look for any defect in the RAM and the DIMM slots. If there are try to get it replaced

[Alexcalibur]

Just now, potatoproduction said:

That wouldnt change how the ram goes in the comp just wouldn't start

I haven't examined the difference between the two, but I know DDR2 and DDR3 is different physically. I assume DDR4 is different aswell

[SarfM786]

Ok guys im goint to send some pictures 

[potatoproduction]

Make sure the clips that are on the side of the slot are open

 

[SarfM786]

[SarfM786]

3 minutes ago, ImperialSteele said:

Did you pull back the retention clip?

Yes and only one side has them 

[FloRolf]

1 minute ago, Sarfaraz said:

Yes and only one side has them 

Can you not locate where exactly it's pushing against to? There must be something that blocks it?!

[SarfM786]

1 minute ago, FloRolf said:

Can you not locate where exactly it's pushing against to? There must be something that blocks it?!

Not really.. 

[ImperialSteele]

5 minutes ago, Sarfaraz said:

Ok guys im goint to send some pictures 

 

Real quick heads up, out side of the bag will conduct static electricity, I would take the MoBo off the bag ASAP just to avoid possible shocks.

 

reference

 

 

45 seconds in.

[Sauron]

2 minutes ago, Sarfaraz said:

Yes and only one side has them 

From the pics I see they are in the right way, just push them in. If you're afraid to break the motherboard install it in the case first, so the standoffs will keep it rigid and safe.

[SarfM786]

2 minutes ago, Sauron said:

From the pics I see they are in the right way, just push them in. If you're afraid to break the motherboard install it in the case first, so the standoffs will keep it rigid and safe.

Ok I will continue the build and get back afterwards to see if that works 

[done12many2]

Did you apply a light coat of oil before trying to insert the sticks?  5w-30 is the best weight for DDR4.