Jump to content

Thermal paste aplication and removal

Go to solution Solved by ChaoticChaosx,

Just go with 70% if you can. Doesn't make much of a difference. I use a coffee filter and 70% isopropyl alcohol for both my waterblock and CPU. Works fine. I'm currently using thermal grizzly kyrosheet on a 7800X3D after going from a 3900X. Due to the little cut outs on the new 7000 Ryzen CPUs. Don't want thermal paste getting in there. Spread or not. Not a big deal but rather not deal with it. First time using it and temps are about the same never above 72c (max) in gaming then around 40c - 42c idle. On water though playing a factor of course.

I recently purchased a Ryzen 7 5700x to replace my existing CPU. I would like to know the ideal thermal paste pattern and amount for this processor, using TM30 thermal paste. Additionally, I would like to know the correct way to remove the preexisting thermal paste. I have heard that 95%+ isopropyl alcohol is required for this task, but it is difficult to obtain where I live. Can I use anything with a lower percentage?

Link to comment
Share on other sites

Link to post
Share on other sites

Just go with 70% if you can. Doesn't make much of a difference. I use a coffee filter and 70% isopropyl alcohol for both my waterblock and CPU. Works fine. I'm currently using thermal grizzly kyrosheet on a 7800X3D after going from a 3900X. Due to the little cut outs on the new 7000 Ryzen CPUs. Don't want thermal paste getting in there. Spread or not. Not a big deal but rather not deal with it. First time using it and temps are about the same never above 72c (max) in gaming then around 40c - 42c idle. On water though playing a factor of course.

First watercooled System

Build Name: Frost

OS: Windows 11 Pro 64-bit

Monitor: Alienware AW3423DWF 1800R Curved Ultrawide 3440x1440 QD-OLED 157hz 10 bit 0.1ms

Chassis: Lian Li 011 Dynamic EVO w/ 2x120mm Corsair QL RGB Fans on the bottom 1x120mm on back exhaust

Top Rad & Fans:  Corsair 54mm 360mm w/ 3x120mm Corsair ML Pro RGB Fans

Side Rad & Fans: Corsair 30mm 360mm w/ 3x120mm Corsair QL RGB Fans

Motherboard: Asrock X670E Steel Legend

CPU: AMD Ryzen 7 7800X3D w/ Corsair XC7 RGB Pro w/ Kyrosheet

Memory/RAM: Corsair Dominator RGB DDR5 2x16GB 32GB 6000Mhz

GPU: Asus GeForce RTX 4080 TUF w/ EK-Quantum Vector2 Nickel/Plexi & Backplate

Pump/Reservoir: Corsair XD5 RGB

Coolant: EK Mystic Fog

PSU: EVGA Supernova 1000w G3 w/ custom modmesh black & white cables from cablemod

Boot/OS SSD: Samsung 970 EVO Plus 500GB NVMe

WZ/2042 SSD: Samsung 850 EVO 250GB

Game SSD: Samsung 980 Pro 1TB

Performance/Editing HDD: Western Digital Black 1TB

Storage HDD: Western Digital Blue 1TB

Mouse: Razer Lancehead Tournament Edition/Razer Mamba

Mouse Mat: Corsair MM700 RGB

Keyboard: Razer Ornata Chroma

Microphone: HyperX Quadcast

Headset: Razer Blackshark v2 Pro

Eyewear/Glasses: Gunnar Optiks Razer FPS

Camera: Razer Kiyo Pro

Link to comment
Share on other sites

Link to post
Share on other sites

Ok, thank you!

13 minutes ago, ChaoticChaosx said:

Just go with 70% if you can. Doesn't make much of a difference. I use a coffee filter and 70% isopropyl alcohol for both my waterblock and CPU. Works fine. I'm currently using thermal grizzly kyrosheet on a 7800X3D after going from a 3900X. Due to the little cut outs on the new 7000 Ryzen CPUs. Don't want thermal paste getting in there. Spread or not. Not a big deal but rather not deal with it. First time using it and temps are about the same never above 72c (max) in gaming then around 40c - 42c idle. On water though playing a factor of course.

 

Link to comment
Share on other sites

Link to post
Share on other sites

1 hour ago, J03tz13l said:

I recently purchased a Ryzen 7 5700x to replace my existing CPU. I would like to know the ideal thermal paste pattern and amount for this processor, using TM30 thermal paste. Additionally, I would like to know the correct way to remove the preexisting thermal paste. I have heard that 95%+ isopropyl alcohol is required for this task, but it is difficult to obtain where I live. Can I use anything with a lower percentage?

I used a paper towel to remove the paste off my AIO and 7700X,  then did a 5-dot method for the 7800X3D.

 

As long as the paste covers the CPU, the method doesn't matter.

 

 

"Do what makes the experience better" - in regards to PCs and Life itself.

 

Onyx AMD Ryzen 7 7800x3d / MSI 6900xt Gaming X Trio / Gigabyte B650 AORUS Pro AX / G. Skill Flare X5 6000CL36 32GB / Samsung 980 1TB x3 / Super Flower Leadex V Platinum Pro 850 / EK-AIO 360 Basic / Fractal Design North XL (black mesh) / AOC AGON 35" 3440x1440 100Hz / Mackie CR5BT / Corsair Virtuoso SE / Cherry MX Board 3.0 / Logitech G502

 

7800X3D - PBO -30 all cores, 4.90GHz all core, 5.05GHz single core, 18286 C23 multi, 1779 C23 single

 

Emma : i9 9900K @5.1Ghz - Gigabyte AORUS 1080Ti - Gigabyte AORUS Z370 Gaming 5 - G. Skill Ripjaws V 32GB 3200CL16 - 750 EVO 512GB + 2x 860 EVO 1TB (RAID0) - EVGA SuperNova 650 P2 - Thermaltake Water 3.0 Ultimate 360mm - Fractal Design Define R6 - TP-Link AC1900 PCIe Wifi

 

Raven: AMD Ryzen 5 5600x3d - ASRock B550M Pro4 - G. Skill Ripjaws V 16GB 3200Mhz - XFX Radeon RX6650XT - Samsung 980 1TB + Crucial MX500 1TB - TP-Link AC600 USB Wifi - Gigabyte GP-P450B PSU -  Cooler Master MasterBox Q300L -  Samsung 27" 1080p

 

Plex : AMD Ryzen 5 5600 - Gigabyte B550M AORUS Elite AX - G. Skill Ripjaws V 16GB 2400Mhz - MSI 1050Ti 4GB - Crucial P3 Plus 500GB + WD Red NAS 4TBx2 - TP-Link AC1200 PCIe Wifi - EVGA SuperNova 650 P2 - ASUS Prime AP201 - Spectre 24" 1080p

 

Steam Deck 512GB OLED

 

OnePlus: 

OnePlus 11 5G - 16GB RAM, 256GB NAND, Eternal Green

OnePlus Buds Pro 2 - Eternal Green

 

Other Tech:

- 2021 Volvo S60 Recharge T8 Polestar Engineered - 415hp/495tq 2.0L 4cyl. turbocharged, supercharged and electrified.

Lenovo 720S Touch 15.6" - i7 7700HQ, 16GB RAM 2400MHz, 512GB NVMe SSD, 1050Ti, 4K touchscreen

MSI GF62 15.6" - i7 7700HQ, 16GB RAM 2400 MHz, 256GB NVMe SSD + 1TB 7200rpm HDD, 1050Ti

- Ubiquiti Amplifi HD mesh wifi

 

Link to comment
Share on other sites

Link to post
Share on other sites

Can I use a microfiber cloth with alcohol?

Link to comment
Share on other sites

Link to post
Share on other sites

2 minutes ago, J03tz13l said:

Can I use a microfiber cloth with alcohol?

Yeah.  I mean it's just a sticky paste.  However you clean things will work, it's no more than wiping a goo off metal.

 

 

"Do what makes the experience better" - in regards to PCs and Life itself.

 

Onyx AMD Ryzen 7 7800x3d / MSI 6900xt Gaming X Trio / Gigabyte B650 AORUS Pro AX / G. Skill Flare X5 6000CL36 32GB / Samsung 980 1TB x3 / Super Flower Leadex V Platinum Pro 850 / EK-AIO 360 Basic / Fractal Design North XL (black mesh) / AOC AGON 35" 3440x1440 100Hz / Mackie CR5BT / Corsair Virtuoso SE / Cherry MX Board 3.0 / Logitech G502

 

7800X3D - PBO -30 all cores, 4.90GHz all core, 5.05GHz single core, 18286 C23 multi, 1779 C23 single

 

Emma : i9 9900K @5.1Ghz - Gigabyte AORUS 1080Ti - Gigabyte AORUS Z370 Gaming 5 - G. Skill Ripjaws V 32GB 3200CL16 - 750 EVO 512GB + 2x 860 EVO 1TB (RAID0) - EVGA SuperNova 650 P2 - Thermaltake Water 3.0 Ultimate 360mm - Fractal Design Define R6 - TP-Link AC1900 PCIe Wifi

 

Raven: AMD Ryzen 5 5600x3d - ASRock B550M Pro4 - G. Skill Ripjaws V 16GB 3200Mhz - XFX Radeon RX6650XT - Samsung 980 1TB + Crucial MX500 1TB - TP-Link AC600 USB Wifi - Gigabyte GP-P450B PSU -  Cooler Master MasterBox Q300L -  Samsung 27" 1080p

 

Plex : AMD Ryzen 5 5600 - Gigabyte B550M AORUS Elite AX - G. Skill Ripjaws V 16GB 2400Mhz - MSI 1050Ti 4GB - Crucial P3 Plus 500GB + WD Red NAS 4TBx2 - TP-Link AC1200 PCIe Wifi - EVGA SuperNova 650 P2 - ASUS Prime AP201 - Spectre 24" 1080p

 

Steam Deck 512GB OLED

 

OnePlus: 

OnePlus 11 5G - 16GB RAM, 256GB NAND, Eternal Green

OnePlus Buds Pro 2 - Eternal Green

 

Other Tech:

- 2021 Volvo S60 Recharge T8 Polestar Engineered - 415hp/495tq 2.0L 4cyl. turbocharged, supercharged and electrified.

Lenovo 720S Touch 15.6" - i7 7700HQ, 16GB RAM 2400MHz, 512GB NVMe SSD, 1050Ti, 4K touchscreen

MSI GF62 15.6" - i7 7700HQ, 16GB RAM 2400 MHz, 256GB NVMe SSD + 1TB 7200rpm HDD, 1050Ti

- Ubiquiti Amplifi HD mesh wifi

 

Link to comment
Share on other sites

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×