loop order any ideas?

[thrasher_565]

so any ideas on what you would do with the loop order? i only have a few 90 degree fittings left i have male to male non swivel, 2 argb flow meters, 2 filters with 90 degrees on them. soft tubing. trying not to block the lcd screens on the pumps and cpu block. each loop will have a top and bottom rad.

distroplate has 2 zones.

 

i think i want to do a 90 degree out of the pump (not ideal) and go up from there.

 

 

Phanteks Glacier D140 Distribution Plate argb

2x bykski argb flow indicator b-fmpa-v2-x

2x HEATKILLER Tube 200 D5 – Multi-Port Glass Reservoir with D5 Pump Mount

2x Aquacomputer -Filter with stainless steel mesh, ball valves

cpu block aquacomputer cuplex kryos NEXT with VISION, acrylic/nickel

gpu block Alphacool Eisblock aurora active backplate (13043) , Alphacool Eisblock aurora acryl-gpx-n-rtx-3080-3090-ftw3 water block

2x Alphacool 17467 Aurora Plexi X4 D-RAM Water Block Water

3x Alphacool 11969 HDX Apex Acrylic aRGB M.2 2280 water block

nb water block koolance GPU-210 Cold Plate

vrm HEATKILLER® SW-X 60 DIY LT water block

 

 

 

Edited April 4, 2025 by thrasher_565

[jaslion]

You've got so much thermal mass for a 3090 + some cpu even if its a 14900k furnace that it doesnt matter.

 

So loop order just have it be the easiest way to connect the tubing.

[thrasher_565]

2 minutes ago, jaslion said:

You've got so much thermal mass for a 3090 + some cpu even if its a 14900k furnace that it doesnt matter.

 

So loop order just have it be the easiest way to connect the tubing.

ya i agree. cooling wont be a problem. flow rate might. im thinking to push up to the top and work the way down some how.

 

cpu i97920x delided witch direct mount.

[jaslion]

6 minutes ago, thrasher_565 said:

ya i agree. cooling wont be a problem. flow rate might. im thinking to push up to the top and work the way down some how.

 

cpu i97920x delided witch direct mount.

I mean a single d5 is plenty good for this. They are strong pumps as long as you just use a clear liquid they dont have any problems at all. Dont even need 2 here in any way.

 

As for gravity helped that can work but the real killer of flow is longer and extra tubing runs. Another big killer is too many flow impedements, basically too many tubes to attachment to tubes again as every tub you connect will have a nozzle on a rad and such thats slightly smaller than the inner diamter of the tube which gives some resistance. So if you can avoid both jn any way do so

[thrasher_565]

2 minutes ago, jaslion said:

I mean a single d5 is plenty good for this. They are strong pumps as long as you just use a clear liquid they dont have any problems at all. Dont even need 2 here in any way.

 

As for gravity helped that can work but the real killer of flow is longer or extra tubing runs. So if you can avoid those in any way do so

ya i could have reduced the vary top and vary bottom rad tubes by swapping them around but what is done is done.

 

its 2 loops so res pump 2 rads for gpu and res pump 2 rads for cpu.

 

gpu is baisicly pumpres> vary top rad> gpu> backplate> then dont no some bottom rad and back to res

 

for cpu its pumpres> im thinking like right ram block or right vrm block then from there i dont no. would be nice to go from pump in to cpu block but i think the 90 degree on the in would block the lcd? has to be one 90 degree as 2 fittings wont fit and i dont have any mope spacer.

[NorKris]

i think its going to be too busy to be looking good

[thrasher_565]

4 hours ago, NorKris said:

i think its going to be too busy to be looking good

well its kinda a meme build. argb everything. and i wanted water cooling but they dont make mb water blocks anymore there all mono blocks. thats why i went with x299 for the duel ram slots and mb has argb on it in the slots.

 

maybe i should take out one m.2 in the middle as its going to be blocked by pcie extension anyway.

 

back in the day people would use fittings as there tube but i cant afford to do so.

 

there is ways to bend the tube tighter but im not going to do that.

 

my old build was like this so should be fine.

 

dont argb everything its a pita for wires... controllers and pinouts...one and done ill probly be done with argb after this...

 

 

Edited April 5, 2025 by thrasher_565

[NorKris]

1 hour ago, thrasher_565 said:

well its kinda a meme build. argb everything. 

expensive meme broski   

[thrasher_565]

10 hours ago, NorKris said:

expensive meme broski   

some one got to do it...