Jump to content
Search In
  • More options...
Find results that contain...
Find results in...

EVGA RTC 2080 XC Ultra problem with display port

I've upgraded to the above from a GTX 970 xc. Super excited but a bit short lived. Before putting the new card in my system I did all the proper removal steps of the old card in device manager and removed old display drivers, also dlded the new ones to use once installed.

Installation went without a hitch. Posted into windows and proceeded to installed the new drivers. Card was detected and installation was completing and then the screen went blank. This has happened before when installing drivers so no cause for concern, however the screen never came back on and the monitor showed that no cable was plugged in. I left the process alone for about 5 mins and still nothing. Performed a shutdown and restarted. There's picture/display when starting up Mobo logo works etc, but when the screen switches to windows log on it goes blank.

System specs: 
Monitor BenQ xl2730
Mobo gigabyte aorus gaming 7

I'm at a loss here any help is appreciated and I hope this is posted in the right section. If anymore info is needed please ask.

 

edit: monitor shows no signal detected, apologies

Link to comment
Share on other sites

Link to post
Share on other sites

did u try the other display ports on the card? might need to reinstall windows, no need to panic yet, since it posts

5950x 1.33v 5.05 4.5 88C 195w ll R20 12k ll drp4 ll x570 dark hero ll gskill 4x8gb 3666 14-14-14-32-320-24-2T (zen trfc)  1.45v 45C 1.15v soc ll evga non-3090 tie ftw3 1905 0.8v 65C 270w (double fps of 1080ti) ll samsung 970 500gb nvme os ll sandisk 4tb ssd ll all nf12/14 fans ll tt gt10 case ll evga g2 1300w ll w10 pro ll 34GN850B ll x27 ll PA272w

 

9900k 1.36v 5.1avx 4.9ring 85C 195w (daily) 1.02v 4.3ghz 80w 50C R20 temps score=5500 ll D15 ll Z390 taichi ult 1.60 bios ll gskill 4x8gb 14-14-14-30-280-20 ddr3666  bdie 1.45v 45C 1.22sa/1.18 io  ll EVGA non-30 tie XC 1830//7600 0.85v 210w ll  8x nf12/14 fans 2x samsung 860 evo 500gb raid 0 ll 500gb nvme 970 evo ll Corsair graphite 780T ll EVGA P2 1200w ll Windows 10 Pro ll NEC PA242w (movie, work mon dying) 1080p 60hzll Predator X27 4k144 hdr (using at 4:4:4 98 fan is dying)

 

 

Link to comment
Share on other sites

Link to post
Share on other sites

I have tried them all, same result.

 

I've tried booting in safe mode and I get display. Used ddu to remove all display drivers and booted in normal mode and was able to get display as well. However when installing the drivers 416.96 I think, same thing blank screen.

 

I don't have an HDMI cable I might have to try that FML, got this card on Kijiji and it was an unopened, sealed box there should be no issue. I've also registered the product with EVGA on their website. 

 

Never had this happen...

Link to comment
Share on other sites

Link to post
Share on other sites

I've posted on the EVGA forums as well, I've gotten some help there with the safe mode procedure. Also got asked if the display port cable is Vesa, If not I'd have problems. Why would it not be?

Link to comment
Share on other sites

Link to post
Share on other sites

So before the new card installation I was running my 970 at 1440p and 144hz. I think this is where the problem lies. I got frusiamd reinstalled Windows, all was fine until I set the resolution to 1440p and 144hz. The the display went blank. Now again I can't get display when getting into windows. Is there a fox for this, have I missed something...

Link to comment
Share on other sites

Link to post
Share on other sites

Have you tried using older drivers? Like using DDU to clean, then install an older one and keep testing to see if it still happens?

Link to comment
Share on other sites

Link to post
Share on other sites

I've used DDU to clean the driver installation in Win10 Safe mode. But as stated above now I can't get to the log on screen and my display goes blank. This is so frustrating as I reinstalled windows for the 23094839 time with this build, just encountered so many hiccups.

 

I may have to go into safe mode again, unistall the card from device manager, ddu the drivers again and see if I can get into windows that way. I've seen that drivers 416.34 were the last to work with RTX cards and xl2730 monitors using 144hz so I'll try that. Failing that I may have to use 120hz which is also a pseudo solution found on the net.

 

Apparently Nvidia and BenQ are aware but there's no progress, they've been aware since 416.81 apparently.

 

New meme RTX ON Megahertz OFF FML, what else can go wrong now... <really frustrated>

Link to comment
Share on other sites

Link to post
Share on other sites

3 hours ago, Htrlo said:

I've used DDU to clean the driver installation in Win10 Safe mode. But as stated above now I can't get to the log on screen and my display goes blank. This is so frustrating as I reinstalled windows for the 23094839 time with this build, just encountered so many hiccups.

 

I may have to go into safe mode again, unistall the card from device manager, ddu the drivers again and see if I can get into windows that way. I've seen that drivers 416.34 were the last to work with RTX cards and xl2730 monitors using 144hz so I'll try that. Failing that I may have to use 120hz which is also a pseudo solution found on the net.

 

Apparently Nvidia and BenQ are aware but there's no progress, they've been aware since 416.81 apparently.

 

New meme RTX ON Megahertz OFF FML, what else can go wrong now... <really frustrated>

Anyone have suggestions on how I can roll back the resolution and refresh rate in safe mode so that the monitor will be able to display in windows normal boot. @xg32 , @Kibelok

Link to comment
Share on other sites

Link to post
Share on other sites

9 hours ago, Htrlo said:

Anyone have suggestions on how I can roll back the resolution and refresh rate in safe mode so that the monitor will be able to display in windows normal boot. @xg32 , @Kibelok

Do you have another computer or laptop where you can download the older drivers, then put it in a USB and try installing it while in Safe mode? This way you can maybe access the control panel and change resolution/refresh rate.

Link to comment
Share on other sites

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share


×