Jump to content

Good overclock ?

Hi Guys Hope your well :)
By Hi Guys Hope your well :)
in Graphics Cards
 Share
Posted

Hi guys, I have just recently overclocked my Rx 580 8gb sapphire nitro + Le 1450mhz boost clock gpu . I have managed to get this overclocked to core clock of 1500mhz and memory clock of 2175mhz at a temp of 78c when in Valley benchmark extreme HD. The core voltage has been upped to 87+ increase out of 100% voltage. As it’s my first time overclocking , do these Numbers seem okay ? Especially the core voltage as I know if you have that to high it can cause a few problems but the system seems to run stable at the numbers I’ve shown . Any advice ? Thankyou very much -_-

Link to comment
Share on other sites
Link to post
Share on other sites
Posted

what about the power limit?

CPU: i7-2600K 4751MHz 1.44V (software) --> 1.47V at the back of the socket Motherboard: Asrock Z77 Extreme4 (BCLK: 103.3MHz) CPU Cooler: Noctua NH-D15 RAM: Adata XPG 2x8GB DDR3 (XMP: 2133MHz 10-11-11-30 CR2, custom: 2203MHz 10-11-10-26 CR1 tRFC:230 tREFI:14000) GPU: Asus GTX 1070 Dual (Super Jetstream vbios, +70(2025-2088MHz)/+400(8.8Gbps)) SSD: Samsung 840 Pro 256GB (main boot drive), Transcend SSD370 128GB PSU: Seasonic X-660 80+ Gold Case: Antec P110 Silent, 5 intakes 1 exhaust Monitor: AOC G2460PF 1080p 144Hz (150Hz max w/ DP, 121Hz max w/ HDMI) TN panel Keyboard: Logitech G610 Orion (Cherry MX Blue) with SteelSeries Apex M260 keycaps Mouse: BenQ Zowie FK1

 

Model: HP Omen 17 17-an110ca CPU: i7-8750H (0.125V core & cache, 50mV SA undervolt) GPU: GTX 1060 6GB Mobile (+80/+450, 1650MHz~1750MHz 0.78V~0.85V) RAM: 8+8GB DDR4-2400 18-17-17-39 2T Storage: HP EX920 1TB PCIe x4 M.2 SSD + Crucial MX500 1TB 2.5" SATA SSD, 128GB Toshiba PCIe x2 M.2 SSD (KBG30ZMV128G) gone cooking externally, 1TB Seagate 7200RPM 2.5" HDD (ST1000LM049-2GH172) left outside Monitor: 1080p 126Hz IPS G-sync

 

Desktop benching:

Cinebench R15 Single thread:168 Multi-thread: 833 

SuperPi (v1.5 from Techpowerup, PI value output) 16K: 0.100s 1M: 8.255s 32M: 7m 45.93s

Link to comment
Share on other sites
Link to post
Share on other sites
Posted
  • Author
45 minutes ago, meme smurf said:

temps are a fair bit higher then what i like, ive overclocked the hell out of my 1050 ti and it doesnt go over 45c when under load. thats because all my fans are at max. if you dont mind a bit of noise try upping your fan speeds just a little bit more would be nice if you could bring that down a fair bit other then that pretty good overclock i would say.

Which fans are you talking about ? System or the fans on gpu , thanks for the reply 

 

Link to comment
Share on other sites
Link to post
Share on other sites
Posted
23 minutes ago, Hi Guys Hope your well :) said:

Power limit is set to 91 on MSI Afterburner max 

why not get that to whatever maximum value? 91 is below stock...

CPU: i7-2600K 4751MHz 1.44V (software) --> 1.47V at the back of the socket Motherboard: Asrock Z77 Extreme4 (BCLK: 103.3MHz) CPU Cooler: Noctua NH-D15 RAM: Adata XPG 2x8GB DDR3 (XMP: 2133MHz 10-11-11-30 CR2, custom: 2203MHz 10-11-10-26 CR1 tRFC:230 tREFI:14000) GPU: Asus GTX 1070 Dual (Super Jetstream vbios, +70(2025-2088MHz)/+400(8.8Gbps)) SSD: Samsung 840 Pro 256GB (main boot drive), Transcend SSD370 128GB PSU: Seasonic X-660 80+ Gold Case: Antec P110 Silent, 5 intakes 1 exhaust Monitor: AOC G2460PF 1080p 144Hz (150Hz max w/ DP, 121Hz max w/ HDMI) TN panel Keyboard: Logitech G610 Orion (Cherry MX Blue) with SteelSeries Apex M260 keycaps Mouse: BenQ Zowie FK1

 

Model: HP Omen 17 17-an110ca CPU: i7-8750H (0.125V core & cache, 50mV SA undervolt) GPU: GTX 1060 6GB Mobile (+80/+450, 1650MHz~1750MHz 0.78V~0.85V) RAM: 8+8GB DDR4-2400 18-17-17-39 2T Storage: HP EX920 1TB PCIe x4 M.2 SSD + Crucial MX500 1TB 2.5" SATA SSD, 128GB Toshiba PCIe x2 M.2 SSD (KBG30ZMV128G) gone cooking externally, 1TB Seagate 7200RPM 2.5" HDD (ST1000LM049-2GH172) left outside Monitor: 1080p 126Hz IPS G-sync

 

Desktop benching:

Cinebench R15 Single thread:168 Multi-thread: 833 

SuperPi (v1.5 from Techpowerup, PI value output) 16K: 0.100s 1M: 8.255s 32M: 7m 45.93s

Link to comment
Share on other sites
Link to post
Share on other sites
Posted

Post a screenshot of your Afterburner. Then we can understand what your doing. The GPU fan can use a custom fan curve creating using Afterburner. This will allow you to reduce temperature a lot (probably). 78c is not that hot but valley benchmark is very old now and not used anymore. You should use furmark to test stability, your GPU will probably overheat using it if your already at 78 on an old program like valley. For proper benchmarking you should use 3DMark.

Gaming Rig:CPU: Xeon E3-1230 v2¦RAM: 16GB DDR3 Balistix 1600Mhz¦MB: MSI Z77A-G43¦HDD: 480GB SSD, 3.5TB HDDs¦GPU: AMD Radeon VII¦PSU: FSP 700W¦Case: Carbide 300R

 

Link to comment
Share on other sites
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing Graphics Cards

×