PC wont Display

[bluekitty69]

I just installed a custom water loop and got a 1tb m.2 along with cable extensions. with everything said and done the PC wont post.  build https://pcpartpicker.com/list/w4LQsJ

[yathis]

is the monitor power on?

is the monitor data cable plugged in?

reseat the gpu

[Trekt Nation]

Check for leaking

[bluekitty69]

it will boot for like 5 mins but i dont get anything on screen and my back lit keyboard doesnt lit up 

 

[bluekitty69]

9 minutes ago, Trekt Nation said:

Check for leaking

no leaks

 

[bluekitty69]

10 minutes ago, yathis said:

is the monitor power on?

is the monitor data cable plugged in?

reseat the gpu

yes

yes

did that and still same things

[yathis]

uninstall then reinstall drivers

try a different slot for the gpu

[bluekitty69]

Just now, yathis said:

uninstall then reinstall drivers

try a different slot for the gpu

cant when i cant see whats on the screen and its hard to move the slot when its a custom loop to it with water already in it.

 

[xitywampas]

First try holding Ctrl while booting. If that doesn't work reset the UEFI(bios) then if it doesn't display re-seat the GPU. Let us know what happens.

[bluekitty69]

i re-seated the GPU and did all that and nothing

i dont think my keyboard is getting power to it i tried different spots and still nothing will light up

[xitywampas]

Check the 24pin ATX connector at the board and PSU if its modular. look for a pushed out pin or something like that.

[bluekitty69]

all pins are good

[xitywampas]

If you have a USB drive or anything else that will light up when powered by USB use that to see if USB is getting power.

 

[bluekitty69]

did that and i got no light when it lit up on my other pc

 

[xitywampas]

You have a 5 volt power problem. It may be something on the board or the PSU. Check for shorts and short to ground. Look everything over make sure it's all connected and nothing metal touches pins on the back of the board. Lastly try a different PSU if possible. If it works with another PSU then you need to replace it. A lot can happen to a system when you disassemble and reassemble it much care is needed.

[Quaker]

I'd start by resetting the CMOS/BIOS/UEFI. Using the hardware CMOS jumper would be best. Next to that, use whatever key during boot-up to enter the BIOS/UEFI (check the manual) and "Load Defaults"

 

Also, check that the motherboard is compatible with the M.2 drive, especially if it's NVMe.

[xitywampas]

 

4 hours ago, Quaker said:

I'd start by resetting the CMOS/BIOS/UEFI. Using the hardware CMOS jumper would be best. Next to that, use whatever key during boot-up to enter the BIOS/UEFI (check the manual) and "Load Defaults"

 

Also, check that the motherboard is compatible with the M.2 drive, especially if it's NVMe.

No post. Black screen. No 5volt a MB. Clear CMOS already suggested. Board is compatible although it may need a UEFI update but it should post.

 

[bluekitty69]

so what it was the cpu block wasnt making contact with the cpu. I have no idea why it would do that when its just not making contact but its up and running now thanks everyone

 

[xitywampas]

On 6/28/2017 at 7:02 AM, bluekitty69 said:

so what it was the cpu block wasnt making contact with the cpu. I have no idea why it would do that when its just not making contact but its up and running now thanks everyone

 

Almost instant overheat probably.