XMP NOT WORKING?

[charbel1011]

I can't set my xmp on for some reasons i have asus z170a and i have the g skills 3000mhz rams and it was working before the bios update the xmp perfectly fine now after i updated bios when i set xmp and restart my computer won't post till i disable it what should i do?

[Jumper118]

Put the settings in yourself or go back to the older bios

[charbel1011]

Just now, Jumper118 said:

Put the settings in yourself

I can't they are locked

[auraofjason]

Since you have an asus board try setting these under dram timing control in the bios:

 

MRC Fast Boost -> [Enabled]
MCH Full Check -> [Disabled]

[Oshino Shinobu]

Was there are specific reason you updated the BIOS? If not, you could roll back to the previous BIOS you know worked. 

[Jumper118]

Just now, charbel1011 said:

I can't they are locked

Pretty sure they aren't lol. 

[charbel1011]

Just now, Jumper118 said:

Pretty sure they aren't lol. 

How 

 

4 minutes ago, auraofjason said:

Since you have an asus board try setting these under dram timing control in the bios:

 

MRC Fast Boost -> [Enabled]
MCH Full Check -> [Disabled]

What's that?

[Jumper118]

3 minutes ago, charbel1011 said:

How 

 

What's that?

Were it says ram speed it will probably say auto atm. Just change it to 3000. Also there will be some option to change the timings and the first 4 will be say 18-19-19-38 (it will say these on the sticker on the ram)  and you can type those in next to the first of those in the bios. 

[charbel1011]

Just now, Jumper118 said:

Were it says ram speed it will probably say auto atm. Just change it to 3000. Also there will be some option to change the timings and the first 4 will be say 18-19-19-38 (it will say these on the sticker on the ram)  and you can type those in next to the first of those in the bios. 

Everytime i change it to 3000 instead of auto and try to save my computer won't post, and i can't type next to the those because it says auto and i cannot do anything to them. believe it or not.

[Jumper118]

Just now, charbel1011 said:

Everytime i change it to 3000 instead of auto and try to save my computer won't post, and i can't type next to the those because it says auto and i cannot do anything to them. believe it or not.

Can you post a picture of the bios screen also did you set the ram voltage as well? 

[charbel1011]

Just now, Jumper118 said:

Can you post a picture of the bios screen also did you set the ram voltage as well? 

I can't set anything in dram timing control page dude

[Jumper118]

2 minutes ago, charbel1011 said:

I can't set anything in dram timing control page dude

Do you need to change some setting to be able to change them? Are they just greyed out? It is hard to know what you are working with when I cant see the bios.

[charbel1011]

8 minutes ago, Jumper118 said:

Do you need to change some setting to be able to change them? Are they just greyed out? It is hard to know what you are working with when I cant see the bios.

What do i need to change only timings?

[auraofjason]

18 minutes ago, charbel1011 said:

What's that?

It disables some weird checking that asus boards do at post which can cause the board to not post. I couldn't get my ram at the xmp rating until I made those changes.

[Jumper118]

5 minutes ago, charbel1011 said:

What do i need to change only timings?

Yes. Just first 4

[charbel1011]

20 minutes ago, Jumper118 said:

Yes. Just first 4

Ok i managed to change it from auto so, the first 4 in dram timing control page is Dram CAS# latency second one is DRAM RAS # to CAS# Delay third one is DRAM RAS# ACT TIME and fourth one is DRAM COMMAND rate and this one i can only change it from auto to 1n or 2n or 3n or N:1 and my rams settins are ddr 3000 and timing is 15-15-15-35 CAS  latency 15 voltage 1.35v where should i put these settings?

[Jumper118]

7 hours ago, charbel1011 said:

Ok i managed to change it from auto so, the first 4 in dram timing control page is Dram CAS# latency second one is DRAM RAS # to CAS# Delay third one is DRAM RAS# ACT TIME and fourth one is DRAM COMMAND rate and this one i can only change it from auto to 1n or 2n or 3n or N:1 and my rams settins are ddr 3000 and timing is 15-15-15-35 CAS  latency 15 voltage 1.35v where should i put these settings?

OK well the first 3 should be in the correct order. For the dram command rate you want 1n. Then maybe the one below that will be 35. The dram voltage needs to be put in under the dram voltage bit which will probably be near the cpu voltage in the bios normal below it.