Vengeance with Hyper 212?

[Bluejay0]

Will a Hyper 212+ have enough clearance for a Corsair Vengeance Standard?

[Samdb]

It's fine I think.

[Hazy125]

Probably, if not you can just raise the fan a few millimetres and it should be fine

[Weesnaw]

 

If that's the standard shape, the slot closest to the fan in push may be blocked.

 

Mine was blocked on a my 1155 motherboard.

[Bluejay0]

If that's the standard shape, the slot closest to the fan in push may be blocked.

Mine was blocked on a my 1155 motherboard.

What motherboard do you have?

[mgsstar]

As shown here: http://www.neogaf.com/forum/showpost.php?p=37873743&postcount=9348

 

It seems to have some space in between but the person chose the low profile version. So if you don't fill up the four slots completely I think you should be fine. 

[Bluejay0]

I have the same board! If I switched for a corsair sp120 could that have a different outcome

[Weesnaw]

I have the Z77 UP4-TH from Gigabyte.

[Emperor_Piehead]

I have the same board! If I switched for a corsair sp120 could that have a different outcome

No they are the same dimesions. If you are just using 2 dimms you will be fine at most it will block the first dimm slot. 

[fishymamba]

Go with the low profile vengeance RAM. It is the same RAM with a shorter heat spreader. 

[D3MON]

depends what you mean by standard, if you mean the high stuff then it may depending on the board, the standard height stuff will....

 

it kinda fits in the second pic but the fan is actually bending the dimm over and putting pressure on the dimm slot, i dont reccomend this...

[kaneandtaker]

It depends on your motherboard. The distance between the CPU socket and RAM slots.

[eslagrassa]

2 dimms are fine. But just saying, installing that cooler is pain in the ...

[JupiteL]

Recently built a computer for my friend using the exact things you mentioned. They're fit together don't worry

[NeutronGTX]

if it's such a major problem, install the fan on the side of the cooler that faces away from the dimms

[iAsuno]

if you only have 2 RAM sticks, then there should be no problem. dunno about 4 though.

[Bluejay0]

What I drew air from the back of the case?

[mgsstar]

What I drew air from the back of the case?

You mean doing a pull config blowing to the rear of the case? That would work since its not the cooler that blocks it its the fan.

[Bluejay0]

You mean doing a pull config blowing to the rear of the case? That would work since its not the cooler that blocks it its the fan.

Ok what about clearance with a NH-D14?

[mgsstar]

Ok what about clearance with a NH-D14?

Nope the NH D14 does not support Vengeance ram: http://www.noctua.at/main.php?show=compatibility_ram_gen&products_id=34&lng=en#DDR3_Corsair

[Bluejay0]

Nope the NH D14 does not support Vengeance ram: http://www.noctua.at/main.php?show=compatibility_ram_gen&products_id=34&lng=en#DDR3_Corsair

 

what if the fans were drawing air from rear?

[mgsstar]

what if the fans were drawing air from rear?

It would be pretty tight if it did fit or it might not even fit and I am not sure about your board because I don't see a image with a NH D14 with your board. This user only had the first slot blocked but not sure what his motherboard is: http://www.overclock.net/t/807307/heatsink-clearance-cpu-and-ram-will-my-cooler-fit/10#post_13884380