Tube running... Confusing, need help

[AMD Lover]

So I drew up a little diagram. Is this the best way. Use your imagination, you should be able to figure out what blob is what.

[werto165]

Personally I think Water Closet runs are terribly messy. 

[gazabi]

Looks fine, but I think the front radiator flow directions are switched; its both receiving and sending water into the reservoir.

[airdeano]

mmm, don't believe you'll get the front and floor radiator to co-exist too well. the

clearances there are so close. if thats a 280, then deffo not going to fit. if it is

a 240 (short) then the floor rad (30mm with one fan set) will fit.

 

a 360x 45 in the roof and 240x 60 in the front intake or floor (best option with

a filter) will hold your fan speed sub 1100 rpm easily with overclocking with high

voltages. if planning on 2x GPU, then the voltage will need to be lower or fan

speed should be increased.

 

lastly, the basement with a rad inside will not be a best option as the heated air

has no place to exhaust.

[AMD Lover]

mmm, don't believe you'll get the front and floor radiator to co-exist too well. the

clearances there are so close. if thats a 280, then deffo not going to fit. if it is

a 240 (short) then the floor rad (30mm with one fan set) will fit.

 

a 360x 45 in the roof and 240x 60 in the front intake or floor (best option with

a filter) will hold your fan speed sub 1100 rpm easily with overclocking with high

voltages. if planning on 2x GPU, then the voltage will need to be lower or fan

speed should be increased.

 

lastly, the basement with a rad inside will not be a best option as the heated air

has no place to exhaust.

Yeah, most of that is covered. The reason they're are thin rads. (I Believe they're all 30mm) is because I want white ones and those were the only ones I could find unless I painted some black ones.

 

21mm Core, 40mm thick

[airdeano]

alphacool offers white rads. some specialty shops offer painting services, too.

or paint the black ones.

[brandishwar]

I've built two loops into the 750D and you used a tube layout similar to how I originally tubed up my wife's build (see my signature for links to build logs).

 

A couple things to point out on the 750D for mounting a front radiator and still allowing for a bottom radiator. First, the front radiator should be a 240mm at most, and you're going to want to mount it using the vent holes in the front area. You'll see that the holes marked "120" and spaced for a 240mm radiator line up with other holes in the front. If you want to fit a 240mm radiator on the bottom of the case, you'll need to use those holes for mounting the radiator, something I point out here. You'll also end up with the front 140mm fans directly over the radiator.

 

On the bottom radiator, that will only work if you're using a short power supply. My wife's RM1000 (180mmlong) barely fits with the bottom radiator, but my AX860 plays nicer.

[AMD Lover]

alphacool offers white rads. some specialty shops offer painting services, too.

or paint the black ones.

Alphacool does offer white rads which would work great until I got to the top 360mm rad in which case I think it would push against my CPU power cables.

[airdeano]

their XT45 360 fits just fine in the stock location or if your cut the ODD bays out

then the UT60 360 fits with dominator platinums and the 8-pin is no issue.

[AMD Lover]

their XT45 360 fits just fine in the stock location or if your cut the ODD bays out

then the UT60 360 fits with dominator platinums and the 8-pin is no issue.

They don't have a white XT45

[airdeano]

seems they have stopped producing them in XT. paint 'em or get them painted.

no need in shortcutting performance over the aesthetics.