Jump to content

RAM Frequency Problem 2133 -> 3600 Solved

BLACKRIPPER
 Share
Go to solution Solved by BLACKRIPPER,

Solved, I put DIMM4 in DIMM2 because HYNIX is on A1/A2 and Samsung is on B1/B2 DIMM3 and 4. Now xmp works just fine, without adjusting. Thanks for your assist @SorryClaire.

 

Posted

Hey guys, recently i´ve noticed my RAM(2 kits of F4-3600C18D-32GVK) is running only on 2133mhz instead of 3600mhz. My cpu is a 5900x and MSI MAG X570 TOMAHAWK WIFI. If I enable XMP nothing happens, after reboot it still says it in bios. Manual set ram speed to 3600mhz result in error (Memory Overclock failed, Press xyz). Can u guys give me a hint, thanks

GPU: Powercolor 7900XTX Hellhound, CPU: 5900X, MB: MSI MAG X570 TOMAHAWK WIFI, RAM: 2kits F4-3600C18D-32GVK, PSU: Seasonic Focus GX-1000, Case: BeQuiet 601 Silenced, CPU Cooler: BeQuiet Dark Rock Pro3 + AM4 Plate, NIC: Asus XG-C100F 10G, Soundcard: Creative Sound Blaster Z, 1TB Kingston NVME, Some old SSDs, HDD: 32TB@7200, Beyerdynamic DT 990 Pro 250 Ohm, WQHD 144hz IPS Display

Link to comment
https://linustechtips.com/topic/1498438-ram-frequency-problem-2133-3600-solved/
Share on other sites
Link to post
Share on other sites
Posted
13 minutes ago, BLACKRIPPER said:

Hey guys, recently i´ve noticed my RAM(2 kits of F4-3600C18D-32GVK) is running only on 2133mhz instead of 3600mhz. My cpu is a 5900x and MSI MAG X570 TOMAHAWK WIFI. If I enable XMP nothing happens, after reboot it still says it in bios. Manual set ram speed to 3600mhz result in error (Memory Overclock failed, Press xyz). Can u guys give me a hint, thanks

try reseating yoru cpu, some of your pins might not have contacted the sockets points for the IMC (inntegrated memory controller) of the cpu. After that it should work. Or just manually set the ram to 3600 

Message me on discord (bread8669) for more help 

Quote me if you want me to get notified

 

Current parts list: PCPartPicker Part List

CPU: AMD Ryzen 5 7600 3.8 GHz 6-Core Processor  (Purchased For £175.00) 
CPU Cooler: Thermalright Phantom Spirit 120 SE ARGB 66.17 CFM CPU Cooler  (Purchased For £0.00) 
Motherboard: MSI PRO B650M-A WIFI Micro ATX AM5 Motherboard  (Purchased For £144.99) 
Memory: Corsair Vengeance 32 GB (2 x 16 GB) DDR5-6000 CL30 Memory  (Purchased For £89.99) 
Storage: Crucial P5 Plus 500 GB M.2-2280 PCIe 4.0 X4 NVME Solid State Drive  (Purchased For £0.00) 
Storage: Kingston A400 960 GB 2.5" Solid State Drive  (Purchased For £0.00) 
Video Card: Gigabyte GAMING OC Radeon RX 7800 XT 16 GB Video Card  (Purchased For £448.99) 
Case: Lian Li LANCOOL 205M MESH MicroATX Mini Tower Case  (Purchased For £82.98) 
Power Supply: MSI MAG A850GL PCIE5 850 W 80+ Gold Certified Fully Modular ATX Power Supply  (Purchased For £99.00) 
Total: £1040.95

 

 

 

 

 

 

 

 

 


 

 

 

 

 

Damn this space can fit a 5090 (just kidding, it needs more)

Link to post
Share on other sites
Posted
44 minutes ago, filpo said:

just manually set the ram to 3600 

58 minutes ago, BLACKRIPPER said:

Manual set ram speed to 3600mhz result in error (Memory Overclock failed, Press xyz)

OP have said it. 

 

Try bumping the voltage +0.05-0.1V above the XMP specification, and see if it boots stable. If it isnt working then id say to go down to 3200, and then tighten the timing to C16 or even lower. Youll observe similar performance but more stable on AMD platform as they favor more on latency than speed.

Press quote to get a response from someone! | Check people's edited posts! | Be specific! | Trans Rights

 

Link to post
Share on other sites
Posted
  • Author
9 hours ago, SorryClaire said:

OP have said it. 

 

Try bumping the voltage +0.05-0.1V above the XMP specification, and see if it boots stable. If it isnt working then id say to go down to 3200, and then tighten the timing to C16 or even lower. Youll observe similar performance but more stable on AMD platform as they favor more on latency than speed.

BTW, set it to 1,350V and 3200mhz didnt work

ram.png

GPU: Powercolor 7900XTX Hellhound, CPU: 5900X, MB: MSI MAG X570 TOMAHAWK WIFI, RAM: 2kits F4-3600C18D-32GVK, PSU: Seasonic Focus GX-1000, Case: BeQuiet 601 Silenced, CPU Cooler: BeQuiet Dark Rock Pro3 + AM4 Plate, NIC: Asus XG-C100F 10G, Soundcard: Creative Sound Blaster Z, 1TB Kingston NVME, Some old SSDs, HDD: 32TB@7200, Beyerdynamic DT 990 Pro 250 Ohm, WQHD 144hz IPS Display

Link to post
Share on other sites
Posted
2 hours ago, BLACKRIPPER said:

BTW, set it to 1,350V and 3200mhz didnt work

ram.png

1.35 is nearly dead stock JEDEC spec, i was expecting 1.45 to 1.5V. But yeah, thats a fat bloody oof if its still bad even with that.

Press quote to get a response from someone! | Check people's edited posts! | Be specific! | Trans Rights

 

Link to post
Share on other sites
Posted
  • Author
  • Solution

Solved, I put DIMM4 in DIMM2 because HYNIX is on A1/A2 and Samsung is on B1/B2 DIMM3 and 4. Now xmp works just fine, without adjusting. Thanks for your assist @SorryClaire.

 

GPU: Powercolor 7900XTX Hellhound, CPU: 5900X, MB: MSI MAG X570 TOMAHAWK WIFI, RAM: 2kits F4-3600C18D-32GVK, PSU: Seasonic Focus GX-1000, Case: BeQuiet 601 Silenced, CPU Cooler: BeQuiet Dark Rock Pro3 + AM4 Plate, NIC: Asus XG-C100F 10G, Soundcard: Creative Sound Blaster Z, 1TB Kingston NVME, Some old SSDs, HDD: 32TB@7200, Beyerdynamic DT 990 Pro 250 Ohm, WQHD 144hz IPS Display

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing CPUs, Motherboards, and Memory

×