argb usb controller guide

[thrasher_565]

for an argb controller i recommend nollie controller. (other usb controllers work if you have it already)

 

https://nolliergb.com/

 

https://www.aliexpress.com/w/wholesale-nollie.html?spm=a2g0o.home.search.0

 

can use open rgb or signal rgb for software.

 

https://openrgb.org/

 

https://signalrgb.com/

 

diy:

wled

 

 

Changed up the info on this page is old info and no longer needed.  the info above is what i recommend you do today.  or some Arduino and something like wled. 

Edited November 23, 2025 by thrasher_565

[thrasher_565]

 

 

[WeaselOverlord]

Just registered to say Thank you for this! Great work 

[thrasher_565]

2 hours ago, WeaselOverlord said:

Just registered to say Thank you for this! Great work 

np

[thrasher_565]

more extra sapce

 

[thrasher_565]

lots of sapce

 

[thrasher_565]

space 2

Edited November 12, 2025 by thrasher_565

[thrasher_565]

space 3

 

[thrasher_565]

space 4

[thrasher_565]

Coolman pin out guide

Edited August 16, 2020 by thrasher_565

[thrasher_565]

more space 

[thrasher_565]

AIGO pin out guide

Edited August 27, 2020 by thrasher_565

[thrasher_565]

extra sapace 2

 

[thrasher_565]

more sapce 3

[Netherspark]

Ok now I'm confused.  I've found this image online for the Corsair 3pin connector, showing the pins in the opposite order to what you're showing above.

Are you sure your diagram is correct?

 

 

I've also seen pre-made adapter cables being sold with the red power wire in the middle...

[thrasher_565]

space

[thrasher_565]

space

[Netherspark]

4 hours ago, thrasher_565 said:

ya i triple checked. oh hold on that diagram in not right. the 5v should be on the right of the female connector and on the left of the male

Yeah it looks like they took your image from here and altered it.

[thrasher_565]

6 minutes ago, Netherspark said:

Yeah it looks like they took your image from here and altered it.

i think i took there image and altered it lol

[thrasher_565]

Strips info pics videos:

1

Spoiler

1

1

 

1

1

1

1

1

1

1

1

1

1

Edited November 17, 2020 by thrasher_565

[thrasher_565]

1

rgb/argb Software:

1

Spoiler

1

JackNet RGB Sync:

1

1

OpenRGB:

1

1

signalrgb

1

1

corsair Arduino code

 

1

 

 

 

Edited August 31, 2021 by thrasher_565

[thrasher_565]

space

[modbay.co]

Hello! I just joined to say that I'm in the process of making custom length sleeved rgb cables (because I like torture apparently) and the RGBpx connector from Aqua Computer isn't a JST ph, it is a 1.25mm pitch connector however in fact after some trial and error, I found that it is actually a Molex PicoBlade connector with a 1.25mm pitch.

found here in the UK: https://uk.rs-online.com/web/p/wire-housings-plugs/2799162

Manufacturers part number: 51021-0400

 

[thrasher_565]

space

[modbay.co]

On 2/11/2021 at 3:17 PM, thrasher_565 said:

i have a link Aquacomputer: uses the Mini Micro 1.25mm JST connector

i got theses and they work

I actually tried them and found the wirehousing was a tad too small even though the pitch is the same when compared to a picoblade connector. Will take another look to confirm but I also am using the molex ones right now