Ram Problem?!?!?!?!/Fan Controlling help :D

[Hoda Ali]

Problem N.1:Ram

 

So i have 2 sticks of ram 4 gig each 

 

Model:corsair Vengeance pro :CMY8GX3M2B2133C9R

was running in dual channel mode at 2133mhz and 1.65v and i think and cl9

 

so i got  Crucial Ballistix Tactical 8GB DDR3 1600 CL8 1.5V (BLT8G3D1608DT1TX0)

was thinkin that i got sray running the 2 corsair in dual mode and run this single maybe oc it a bit to 1866mhz

now here the problem i think i can't configure each channel in the bios i think i have to run them all at the same speed tried 1866mhz and 1.650v but the volt was by mistake later changed to 1.5v

but i kept getting pc freezing then restarting and couple of blue screen of DEATH  

 

here's what i caught of the errors :  1.PAGE_FAULT_IN_NONPAGED_AREA (cpuz137_x64.sys)   2.The Famous that i get alot when tweaking around :WHEA_UNCORRECTABBLE_ERROR

 

so i said maybe i need to lower the freq so i went from 1866 to 1600 and run memtest86+ but i don't cuz i never run it took a while to get 1 pass the test took 30min+

 

so i was like 1 pass is enough and stress tested the pc again from 30min i was like yeah then it froze and crash again and now iam running at 1300mhz and 1.5v and cl9

 

so i need to configure the ram 

 

 ------------------------------------------------------------------------------------------------

Problem N.2: Fan Controlling

 

 i want to control my case fans and heatsink to stop at a certain degree and run again at higher temps i graph i mean tried speedfan only control 1 of my fan and all is working 

and the bios doesn't give me any setting for making a graph only pwm/temp ratio

tried gigabyte system information something it worked it has a graph system but when i restart all the setting i made go away it resets so yeah help

 

 

 

Lastly pc specs:

Mb:Gigabyte z87x-oc

Ram:8 gigs of corsair vengeance 2133Mhz

Cpu:4790k

Cooler:Noctua NH-D15 Dual Fan

PSU:Seasonic 750w M12II Bronze full Modular

case:CM 690 III

Gpu:Gtx 650 oc and i know i will upgrade not now

Os:win10 Preview Build 10074

 

 

 

 

[G33k 4 L1F3]

Problem N.1:Ram

So i have 2 sticks of ram 4 gig each

Model:corsair Vengeance pro :CMY8GX3M2B2133C9R

was running in dual channel mode at 2133mhz and 1.65v and i think and cl9

so i got Crucial Ballistix Tactical 8GB DDR3 1600 CL8 1.5V (BLT8G3D1608DT1TX0)

was thinkin that i got sray running the 2 corsair in dual mode and run this single maybe oc it a bit to 1866mhz

now here the problem i think i can't configure each channel in the bios i think i have to run them all at the same speed tried 1866mhz and 1.650v but the volt was by mistake later changed to 1.5v

but i kept getting pc freezing then restarting and couple of blue screen of DEATH

here's what i caught of the errors : 1.PAGE_FAULT_IN_NONPAGED_AREA (cpuz137_x64.sys) 2.The Famous that i get alot when tweaking around :WHEA_UNCORRECTABBLE_ERROR

so i said maybe i need to lower the freq so i went from 1866 to 1600 and run memtest86+ but i don't cuz i never run it took a while to get 1 pass the test took 30min+

so i was like 1 pass is enough and stress tested the pc again from 30min i was like yeah then it froze and crash again and now iam running at 1300mhz and 1.5v and cl9

so i need to configure the ram

------------------------------------------------------------------------------------------------

Problem N.2: Fan Controlling

i want to control my case fans and heatsink to stop at a certain degree and run again at higher temps i graph i mean tried speedfan only control 1 of my fan and all is working

and the bios doesn't give me any setting for making a graph only pwm/temp ratio

tried gigabyte system information something it worked it has a graph system but when i restart all the setting i made go away it resets so yeah help

Lastly pc specs:

Mb:Gigabyte z87x-oc

Ram:8 gigs of corsair vengeance 2133Mhz

Cpu:4790k

Cooler:Noctua NH-D15 Dual Fan

PSU:Seasonic 750w M12II Bronze full Modular

case:CM 690 III

Gpu:Gtx 650 oc and i know i will upgrade not now

Os:win10 Preview Build 10074

Welp. Thats a RAM bluescreen. Time to take off the OC, and test each RAM individually to see if any of them are dead, then together at stock speeds. Mismatching RAM at different OC limits can reek havoc on the OS and on themselves. Its like putting an AMD GPU in with an Nvidia, then running CCC with Nvidia experience.

As for the fans, if they only have a 3pin female connector, they cannot be controlled. If they are PWM (4 pin), I presume by "gigabyte thing", you mean BIOS? If it isnt saving, see if the CMOS battery is dead, or if you are saving then exiting, not exiting without saving, in BIOS.

[das affe]

Welp. Thats a RAM bluescreen. Time to take off the OC, and test each RAM individually to see if any of them are dead, then together at stock speeds. Mismatching RAM at different OC limits can reek havoc on the OS and on themselves. Its like putting an AMD GPU in with an Nvidia, then running CCC with Nvidia experience.

As for the fans, if they only have a 3pin female connector, they cannot be controlled. If they are PWM (4 pin), I presume by "gigabyte thing", you mean BIOS? If it isnt saving, see if the CMOS battery is dead, or if you are saving then exiting, not exiting without saving, in BIOS.

he means an utility gigabyte offers for windows. not a really good one tho..

he just needs to get the timings to match and the speeds too, doesn't he?

[das affe]

Problem N.1:Ram

 

So i have 2 sticks of ram 4 gig each 

 

Model:corsair Vengeance pro :CMY8GX3M2B2133C9R

was running in dual channel mode at 2133mhz and 1.65v and i think and cl9

 

so i got  Crucial Ballistix Tactical 8GB DDR3 1600 CL8 1.5V (BLT8G3D1608DT1TX0)

was thinkin that i got sray running the 2 corsair in dual mode and run this single maybe oc it a bit to 1866mhz

now here the problem i think i can't configure each channel in the bios i think i have to run them all at the same speed tried 1866mhz and 1.650v but the volt was by mistake later changed to 1.5v

but i kept getting pc freezing then restarting and couple of blue screen of DEATH  

 

here's what i caught of the errors :  1.PAGE_FAULT_IN_NONPAGED_AREA (cpuz137_x64.sys)   2.The Famous that i get alot when tweaking around :WHEA_UNCORRECTABBLE_ERROR

 

so i said maybe i need to lower the freq so i went from 1866 to 1600 and run memtest86+ but i don't cuz i never run it took a while to get 1 pass the test took 30min+

 

so i was like 1 pass is enough and stress tested the pc again from 30min i was like yeah then it froze and crash again and now iam running at 1300mhz and 1.5v and cl9

 

so i need to configure the ram 

 

 ------------------------------------------------------------------------------------------------

Problem N.2: Fan Controlling

 

 i want to control my case fans and heatsink to stop at a certain degree and run again at higher temps i graph i mean tried speedfan only control 1 of my fan and all is working 

and the bios doesn't give me any setting for making a graph only pwm/temp ratio

tried gigabyte system information something it worked it has a graph system but when i restart all the setting i made go away it resets so yeah help

 

 

 

Lastly pc specs:

Mb:Gigabyte z87x-oc

Ram:8 gigs of corsair vengeance 2133Mhz

Cpu:4790k

Cooler:Noctua NH-D15 Dual Fan

PSU:Seasonic 750w M12II Bronze full Modular

case:CM 690 III

Gpu:Gtx 650 oc and i know i will upgrade not now

Os:win10 Preview Build 10074

you just gotta get the same speeds and timings for all of your memory sticks. and the gigabyte utility..... forget it..its kinda fucked up.

[Hoda Ali]

so i can set the timing of each channel i set it 9-9-11-31 and 1866mhz but the voltage is the main problem my corsair kit runs at 1.65v at 2133mhz and the crucial one runs at 1.5v at 1600mhz so i ran them at 1866mhz with 1.550v or should i run them at 1.650 or 1.5 but 1.650 i think is too much for the crucial one and 1.5 is low for corsair or maybe not what do u guys think

[0x1e]

If you lower the 2133Mhz ram speed then you can also lower the voltage.

You just need to figure out what voltage that is.

[Abir Vandergriff]

so i can set the timing of each channel i set it 9-9-11-31 and 1866mhz but the voltage is the main problem my corsair kit runs at 1.65v at 2133mhz and the crucial one runs at 1.5v at 1600mhz so i ran them at 1866mhz with 1.550v or should i run them at 1.650 or 1.5 but 1.650 i think is too much for the crucial one and 1.5 is low for corsair or maybe not what do u guys think

1.65V doesn't make too much of a difference with RAM, so if it doesn't work at 1.55V, try 1.6 and then 1.65, if possible.

You never really said what you were doing with your system, so I'll just mention that if you're just gaming, you might as well run all the sticks at the Crucial XMP settings. It should be a lot more stable that way, and won't make any difference in framerate.

[Hoda Ali]

sorry for the late reply i had to study so i found a problem i oced my cpu to 4.5 ghz at 1.180v vcore and 1.850vccin and this was done before the new crucial stick so i never checked for system stabilty ther was a bit of unstablity from the ram side it was mostly cpu 

 

so atm i'm running the 3 stick at 1.5v and 1866mhz and cl 11 13 13 34 needs abit of tweaking but i think i have solved the problem i will do more tweaking and report later and mark as solved if it's stable ty everyone

[Hoda Ali]

so iam running at 1.6v stable with 1866mhz and cl 9-9-11-31 set manually idk about the last timing should i lower the 31 to 29?? but iam stable

 

if any one have any suggestions about the ram 

 

and don't forget the fan controlling anyone know software that controls fans with a graph/slope ?