Jorge4757

Hello everyone I am currently employed as tech support and where I work I encounter this "weird" issue (hopefully there is a specific reason for this), basically its a VOIP Phone that connects trough a VPN tunnel using the internet from lets call it, Office-B to Office-A to the PBX server stored locally. *I will provide a diagram to make it as clear as possible. So I have this IP Phone connected to a 24 hub / really old 10/100 unmanaged switch inside an external warehouse, this switch is connected via Point-to-Point wireless antennas to a switch in the main office to get internet / LAN access; then it goes to the sonic wall appliance and that is connected the ISPs routers in this case AT&T, from there it goes to the VPN tunnel using the internet, in the other end of the tunnel there is a very similar structure but the phone its supposed to reach to the PBX on OFFICE-A which it does but it can only receive calls but it wont make calls, it kinda looks like it goes trough it rings once and choppy and then it says network disconnected. Network Diagram The VOIP phone I am using is a SNOM 300 and I tried to connect the same phone on OFFICE-B directly to the Switch and it will do the same I mentioned above, then I tried to setup the phone on OFFICE-A and it would work just fine, it doesn't matter whether or not its using 10.10.1.x or 172.20.20.x, the phone would work on OFFICE-A just fine. Could you help me troubleshooting this issue or where can I start looking up? Please also let me know if you need more information to begin with or tell me where should I post this so it gets more exposure since I really dont know if its right to put it here in the networking tab. I intended to use wireshark in order to see at what point the packet stops or something similar, but I dont know how to set that up like what cables goes where, it might be an issue considering how much equipment its being used here. More about : troubleshoot voip phone receives calls wont make

Thats great even better that you dont mind views or subs but you really need money or equipment if you wanna at least start something.

I did this Well they are high rpm fans I thought they would work just fine.

I'm sorry didn't state that in the post but it only decrease 3 degrees max.

I know but take a look at this using and msi mobo and gfx as well. *

So here what happens... Where I live we are having really hot temperatures for example just right now it is 39c (102f) as 5:05pm and the room where is my pc located there is no AC unit but I have plenty of air flow (case completely open with 5 120mm fans) I'm expecting high temps anyway but with definitely not the same or worse with a noisier solution... here is my system CPU:AMD Phenom 965BE @3.8Ghz *oc 10Gb DDR3 Ram 1333mhz *1600mhz *oc 300gb Intel DC S3500 Series (boot drive) 240gb Sandisk Extreme 2TB HDD 5900rpm , 1TB HDD 7200rpm, 500gb HDD 7200rpm. MOBO MSI 970a-g46 GFX: MSI Twin Frozr 560 ti PSU: Corsair Cx 750m I have another Delta fan a bit bigger than these cpu fans should I replace one of them? My GTX 560TI Twin Frozr II was at 50-56c idle with the fans stuck at 22% all time even while gaming I had to increase the speed manually always the card is advertised as 22c again I'm expecting high temps given the conditions but seems to high since I am not gaming not even doing OC. **Even though I increase the speed to 100% I wont serious improvement 3 degrees barely. That is why I decide to make a custom cooling ghetto solution but also cleaned at the contact surfaces with alcohol and apply new thermal paste thermalfusion 400 using the finger with a piece of plastic bag technique anyway here is the final result adding old cpu fans (sempron 145 and phenom 965 stock fans) attached to the heat sink of the card with the glorious zip ties. I'll post some pictures during the process. I replace the thermal paste in my cpu for better cooling performance but it seems to decrease it... (if I set 50% on the 7000 rpm fan you cant notice noise and gives the same temps. as 7000rpm but I have to do it manually within speedfan) Something happened when I look up for cpu temps withing windows shows 0c even in HW Monitor its weird since because last week it was fine.

My favorite part is that you Luke and Logan signed that already awesome laptop.

You should post your actual device and speeds but also the advertised speed you are paying for.

Disk Access CPU

seems like nope

-CPU 2GB Micron 4GB A-DATA 2GB PNY 2GB Kingston Hyperx Blue -END OF MB

I don't know exactly what do you mean by interleaving I'm guessing that you mean that is running @667mhz dual channel (DRR3-1333)?

http://k43.kn3.net/77584CC3D.jpg This is a picture.

Yep that's in idle but consider that where I live its 35°c and I don't have and AC unit in the same room with my pc, I have already checked CrystalDiskInfo and only the 2TB its listed as "warning" I've been using that drive for a long time 24/7 the other drives are good two of them were bought during this year including the SSD.