Pc not going into windows

[M0SIE]

When i turn on my pc everything works fine I enter.The start up logo pops up and i get a BSOD with out a stop code and it auto restarts the pc same again my pc turns on fine but no signal to my monitor. It was working fine like a hour ago

 

Ryzen 3 2200g

GTX 1050 2gb

G.Skill RIpjaws DDR4 3200mhz(8gb Duel Channel)

MSI B350M Gaming Pro(With the latest drivers)

Silicon Power Ace 256GB SATA3 SSD

Gamemax 650w Bronze+ PSU

Windows 10 Home 64 bit

[dgsddfgdfhgs]

I think you have not reinstall windows for the APU to work properly

[homeap5]

Looks like hardware failure to me. Of course if I good understand your post.

[C1intFunWood]

Try going into your BIOS and seeing if your motherboard detects your boot drive. If it does, then try getting the Windows 10 installer on a USB and boot off of that and run the Diagnostics tool to fix your boot files. If your motherboard doesn't detect your boot drive, then you might have a bad connection or a dead drive.

[C1intFunWood]

Here is a forum post on the Microsoft site explaining the steps to repair your boot files

 

https://answers.microsoft.com/en-us/windows/forum/windows_10-performance-winpc/repair-windows-10-using-usb-drive/35c9a8f8-dde5-4370-a8fe-5a84b9e00ebb

[M0SIE]

9 minutes ago, dgsddfgdfhgs said:

I think you have not reinstall windows for the APU to work properly

Huh it was literally working fine about an hour ago what reinstall is needed?

[Master Disaster]

12 minutes ago, M0SIE said:

Huh it was literally working fine about an hour ago what reinstall is needed?

Can you read what message the BSOD is giving you? Did you change anything before it stopped booting?

[M0SIE]

Just now, Master Disaster said:

Can you read what message the BSOD is giving you? Did you change anything before it stopped booting?

No code when there was a BSOD I did overclock my cpu from 3.75gz to 3.8gz yesterday 

[Master Disaster]

3 minutes ago, M0SIE said:

No code when there was a BSOD I did overclock my cpu from 3.75gz to 3.8gz yesterday 

First thing is undo the overclock, it's possible thats the issue.

 

There's no code but what does it say? It's important information as it will give some clue as to what's happened. Can you take a picture of it with your phone?

[M0SIE]

31 minutes ago, Master Disaster said:

First thing is undo the overclock, it's possible thats the issue.

 

There's no code but what does it say? It's important information as it will give some clue as to what's happened. Can you take a picture of it with your phone?

I can undo the overclock i tried removing the CMOS battery and it didt work.I couldn’t take the picture because it auto restarted the pc it self but all i remeber there was no stop code

[vaiwalker]

hello fellow singaporean. roll back your overclock. remove rams. insert one ram at a time and see how it goes

[M0SIE]

I just got progress my pc booted to windows and had a BSOD error code of PFN LIST CORRUPT and I restarted and than back like just now pc turns on but no singal on the monitor

[M0SIE]

1 hour ago, vaiwalker said:

hello fellow singaporean. roll back your overclock. remove rams. insert one ram at a time and see how it goes

I just removed one of my ram sticks it booted and went into the bios but when I attempted to boot to windows the pc restarted it self and now the monitor has no signal again

[vaiwalker]

3 minutes ago, M0SIE said:

I just removed one of my ram sticks it booted and went into the bios but when I attempted to boot to windows the pc restarted it self and now the monitor has no signal again

could be that ram thats inside causing the problem. change slots? interchage? tried all the possible combination? or you can try removing the graphics card and using the onboard display. just make sure you change the setting in bios to use on-board display. does it go into safe mode? if it can go into safe mode, it's probably a software issue. should be easy to fix in safe mode

[M0SIE]

9 minutes ago, vaiwalker said:

could be that ram thats inside causing the problem. change slots? interchage? tried all the possible combination? or you can try removing the graphics card and using the onboard display. just make sure you change the setting in bios to use on-board display. does it go into safe mode? if it can go into safe mode, it's probably a software issue. should be easy to fix in safe mode

I did all of the above and i cant enter safe mode if my pc doesn’t even boot or BSOD on boot instantly