Jump to content

I need advice

Ands
By Ands
in Custom Loop and Exotic Cooling
 Share
Posted

Hello everyone, i need advice about this long bend coming from d5 pump. I wanted to make something more interesting with the tubes, but did i made to much? I worried about that long tube can significantly decrease my flow rate. Should i make it shorter? I'm using Alphacool vpp755 d5 pump with double 360  45mm rads. Thanks for answers and im very sorry about my English:) 

IMG_20210120_104935.jpg

Link to comment
Share on other sites
Link to post
Share on other sites
Posted
53 minutes ago, Ands said:

Hello everyone, i need advice about this long bend coming from d5 pump. I wanted to make something more interesting with the tubes, but did i made to much? I worried about that long tube can significantly decrease my flow rate. Should i make it shorter? I'm using Alphacool vpp755 d5 pump with double 360  45mm rads. Thanks for answers and im very sorry about my English:) 

Nice looking build you have there.

 

I wouldn't worry about any flow rate issues. I have a 2 x 360 rads on a CPU + GPU loop in an o11 dynamic with the G1 distro plate that uses a DDC pump and I don't have any issues. That's not to say I don't have a low flow rate but I don't have any noticeable temp or noise problems even when stress testing.

Bedroom PC - Lian-Li O11 XL Evo - Intel Core i5 13600k @ 5.4P / 4.4EGhz -  MSI Pro-A Wifi Z790 Mobo DDR5 - 32GB Ram - Gigabyte RTX 4090 - 1TB Samsung 990Pro NVMe - Corsair HX1200i PSU - Dual Custom Loop Cooling - GPU cooled with EK Quantum Surface S240 + EK Quantum Surface P360M X-Flow Rads - CPU cooled with EK Quantum Surface X360M Rad

 

Living Room PC - Hyte Y60 - Intel Core i9 9900k @ 5Ghz -  MSI Meg Ace Z390 Mobo - 16GB Ram - Palit RTX 3080ti - 256GB Samsung NVMe - Corsair AX850 PSU - CPU + GPU cooled with Hyte Y60 Corner Distro Plate - EK Coolstream S120 + EK Quantum Surface S360 + EK Quantum Surface X240M

 

Extension PC - Lian Li o11 Dynamic - Intel Core i7 8086k @ 5.1Ghz -  Gbyte Z390 I Aorus Pro Wifi Mobo - 16GB Ram - EVGA RTX 2080ti - 256GB Samsung NVMe - EVGA B5 850W PSU - CPU + GPU cooled with dual EKWB 360 Rads + G1 side EKWB distro plate.

 

Office - Thermaltake Tower 100 - Intel Core i7 8700K @ 5.1Ghz - Gbyte Z390 I Aorus Pro Wifi Mobo - 16GB Ram - EVGA GTX 1080ti - 256GB Samsung NVMe - EVGA B5 850W PSU - CPU + GPU cooled with dual EK Quantum Surface P120M Rads + Barrow 3-in-1 Block, Res & Pump.

 

Annex - Corsair 250D - Intel Core i7 3770k - Asus P8Z77 I Delux Mobo - 16GB Ram - EVGA GTX 980ti - 256GB Corsair SSD - BeQuiet P11 750 PSU - CPU cooled with EK Coolstream S240 + S120 Rads + EK Pump / Res Combo

 

Office - Corsair 280X - Intel Core i7 4790k - Asrock H97M ITX Mobo  - 16GB Ram - EVGA GTX 980 - Corsair SFXL600 PSU - CPU + GPU cooled with triple EK Coolstream S240s + EK Pump / Res Combo

 

NAS PC - Fractal Node 804 - Intel Core i7 3770k - Asus P8Z77-M Mobo - 16GB Ram - MSI GTX 1660 Ventus - Corsair AX850 PSU - Unraid 15TB Storage Server

 

Living Room AV Setup 5.1.4 - Yamaha RX-A2060 - 2 x B&W CM9s2 - 2 x Monitor Audio FX Silvers - 4 x B&W CCM665s - B&W CMCs2 - SVS SB13 Ultra - LG OLED65C1

 

Extension AV Setup - Sonos ARC + Sub (Gen 3) - LG OLED65C6V + Yamaha RX-A1070 - 5 x Monitor Audio C265s (2 Zones)

 

Bedroom AV Setup - Yamaha WXC-50 - 2 x B&W CM1s - Rel Quake - LG OLED42C2.

Link to comment
Share on other sites
Link to post
Share on other sites
Posted
  • Author
10 hours ago, ChrisLoudon said:

Nice looking build you have there.

 

I wouldn't worry about any flow rate issues. I have a 2 x 360 rads on a CPU + GPU loop in an o11 dynamic with the G1 distro plate that uses a DDC pump and I don't have any issues. That's not to say I don't have a low flow rate but I don't have any noticeable temp or noise problems even when stress testing.

Thanks, i will upload a new photo then it be finished.

Link to comment
Share on other sites
Link to post
Share on other sites
Posted

D5 pumps are intended for heating systems in your house pushing around water between floors. Stop fussing.

Use the quote function when answering! Mark people directly if you want an answer from them!

Link to comment
Share on other sites
Link to post
Share on other sites
Posted
  • Author

So it is finished. I still need more practice for bending and more straight looking custom loop. The results are quite good but could be better 🙂

IMG_20210124_210234.jpg

Link to comment
Share on other sites
Link to post
Share on other sites
Posted

Nothing to do with your cooling loop, but just wanted to mention - love the quilted PSU shroud, very neat.

Link to comment
Share on other sites
Link to post
Share on other sites
  • 4 weeks later...
Posted
  • Author
On 1/25/2021 at 3:36 PM, BRush00 said:

Nothing to do with your cooling loop, but just wanted to mention - love the quilted PSU shroud, very neat.

Thanks, sadly last weak i had to rebuild because of gpu upgrade, used less 90 degree fittings i made more bends. Here's how it looks now. 

IMG_20210222_173049.jpg

Link to comment
Share on other sites
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing Custom Loop and Exotic Cooling

×