First build, no video.

[grinOn2wheels]

My son and I just finished our first build and everything went smoothly until the first boot.

PC comes on, no beeps. GPU and RAM light up, fans and AIO all running.

I have tried HDMI and DVI but no signal is being detected.

We tried removing the GPU using the 13700k integrated graphics, and tried only using 1 stick of RAM. Clearing/reset CMOS.

I know I need to update the bios for Gen13 Intel but we can't even get the video to show.

Any help would be greatly appreciated, I am way out of my league on this.

Keyboard doesn't light up but the USB ports on the pc case are lit.

Tried a different monitor still no picture. 

The only codes we are getting are:

00

7F

59

54

PC Specs:

Intel 13700k

EVGA Z690 Classified

Kingston Fury Beast RGB 32GB 5600MT/s DDR5 CL40

PowerColor Red Dragon AMD Radeon™ RX 6800 XT

DeepCool Liquid Cooler LT720 360mm

WD_BLACK 1TB SN850 NVMe

Crucial MX500 2TB 3D NAND SATA 2.5

CORSAIR iCUE SP120 RGB ELITE Performance 120mm PWM Triple Fan Kit

CORSAIR iCUE 5000x RGB

Super Flower Leadex Platinum SE 1000W 80+ Platinum,

BenQ BL2711U 4K 

[Harmsway1283]

In your motherboard manual it tells you how to update the BIOS without a CPU on page 144. Give that a shot.

[grinOn2wheels]

I have tried to hot flash the bios but I'm getting either 

E1 S3 Boot Script execution or

E8-EB S3 Resume Failed error codes

depending if I'm using a usb with just the bin file or the EVGA usb with all files 

[Robchil]

6 minutes ago, grinOn2wheels said:

I have tried to hot flash the bios but I'm getting either 

E1 S3 Boot Script execution or

E8-EB S3 Resume Failed error codes

depending if I'm using a usb with just the bin file or the EVGA usb with all files 

shorten the name to 7.3 letters. 7 first part max and .bin the last.  if you havn't done that already. 

[grinOn2wheels]

this is what I used

EVGAE698.bin

According to the manual, that's the naming

[grinOn2wheels]

I even followed this video because my system is fully assembled but still stuck

 

[Robchil]

17 minutes ago, grinOn2wheels said:

this is what I used

EVGAE698.bin

According to the manual, that's the naming

shorten it one letter and try again. 

[Scorpion_3381]

i had the same issue with my second buld.....i forgot to plug in the motherboard....i was a noob then...it took me 3 houres to find it out!

[Scorpion_3381]

just check that its pluged in by the small mb power connector the 4 or 8 pin one, sometimes the most annoying issues are the simple ones lol

[grinOn2wheels]

I have the 24-pin ATX Power Connector & 2x  8 pin EPS Power Connectors attached. I didn't see another one?

[Robchil]

10 minutes ago, grinOn2wheels said:

I have the 24-pin ATX Power Connector & 2x  8 pin EPS Power Connectors attached. I didn't see another one?

the 8 pin EPS connectors can usually be split in the middle.. PCIE connectors detatch 2+6 .. look closer on your eps connector you usually see it on the latch if it's split in the middle, if it is twist it to split them. 

 

[grinOn2wheels]

Why would I split the 8 pin? There is no way to split it. The 2 cables are 8 pins that are the CPU power cables.

I added a 6 pin (8-2 VGA) cable to the Supplemental PCIe 6 pin power on the MOBO but that didn't help.

The only cables from my PSU that split are the VGA 6+2 cables.

[Scorpion_3381]

ok, are there any sockets that are empty on your motherboard?

ones that look like a small 24pin on the top of the motherboard?

[Scorpion_3381]

could you post a photo of your motherboard?

[grinOn2wheels]

I just stripped the MOBO of everything except power and still cannot flash the bios.

But here is a picture before I disassembled it. I have the 24 pin on the right, 2 x 8 pin on the top left

and I added a 6 pin to the bottom left but that didn't change anything.