BabyGroot69

I ran my fans at 1300 rpm and I am able to achieve 60C stress test instead of 70C with boost clocks. Just thought I would share my findings.

I am but I am going to wait for the EK fans. Thanks for the help!

Well i had a dark rock pro 4 before this and I am seeing similar temps but maybe that cooler was just as good at dissipating heat. I am used to seeing 4.4Ghz during gaming but all cores stayed at 4Ghz on prime. As for voltage I have only ever seen 1.1 to 1.2.

That is what I was thinking. I did bleed any large bubbles and now there are just micro bubbles in the res. Thermal paste should be okay. I did pull my block and re-seat it before completing the loop just to make sure I put it on correctly. I guess ill see how the fans do because there also it an dust filter in front the case with pretty small holes.

When I was running prime95, the voltage was 1.1 and 4Ghz so prime wasnt even boosting but when I game, the CPU will boost up to 4.4Ghz.

True. My room was roughly 20C so it was pretty cold so i doubt their room was 10C lower but nothing is impossible. I you guys think its normal temps than I am okay with that.

I was just expecting better temps than that. Not sure how someone can get 10C lower with an EK AIO.

I can only have 3 fans because I have my res mounted to the top of the case in a horizontal position. The noctua fans I have are rated low for static pressure so I bought Ek vardar fans so i am hoping that will help. I know 70C isnt terrible it just was higher than I expected.

Yeah. I already knew they dont make a waterblock for it but I dont want this generation of rtx cards. My question was about the temperature I am getting during stress test.

My GPU is the zotac 1070 ti mini. The 70C stress test is without GPU load. Gaming I average around 50C-60C depending on the game and I am just surprised its not better than my old dark rock pro 4.

Hello, I recently built my first hardline build. I only did my cpu at the moment due to them not making a waterblock for my GPU. My loop consists of a ekwb d5 pump, separate res above, 240mm rad in the front, 120mm rad in the back and the ekwb velocity cpu block. My old build had 2 360mm rads so maybe I am use to lower temperatures but I would like to ask if this is normal anyway. Prime95 v26 I am seeing temps on my 8700k at stock speeds reach 70C on small fft after 30min. Not sure if that seems normal or not. I found a youtube video where an EK 240 AIO was getting better temps than I am. I thought maybe the GPU could be making the temps worse due to the hot air being dumped directly into the rear 120mm rad. Also i ordered some static pressure fans and mine are not rated very high for static pressure. I only have 3 fans inside the case, two on the front rad and one on the rear. Any thoughts? More about : w

I agree but for the basic syntax I think books are okay.

Definitely get a good grasp on Object Oriented Programming. You will most likely learn either Java, C++ or C# in school and having an early understanding of what objects are, how to create them and use them would be great. They will teach you this but the concepts Polymorphism, Abstraction, Inheritance and Encapsulation can at times be confusing when first learning them.

There are plenty of free tutorials to learn java. YouTube, LinkedIn Learning, Coursera, Codecademy, TutorialsPoint, Treehouse as well as tons of books. Eclipse or Intellij for the IDE. **Coursera and Treehouse are not free.

I am pretty sure GPUs don't really go on sale since most people are willing to pay full price. I have seen newegg sell for $50 off but not any more than that.

I had to go out of town, sorry. I inserted the 16gb and checked the timings. They were correct. I also check with XMP enabled and they were correct again. I know this issue is what is causing my BSOD because I haven't had the extra 16gb in for a few weeks and I have had no issues.

Okay I will. I will let you know. Thank you!

I don't poke around in the BIOS when it comes to manually setting values. Everything was set to auto from the manufacturer. I can definitely reinstall them tomorrow and check.

The stop codes varied but I managed to read two that said KMODE_EXECEPTION_NOT_HANDLED and PAGE_FAULT_IN_NONPAGED_AREA. Nothing ever said memory specifically. Both kits were ordered to match. I ordered one kit 2x8 and then ordered the exact same kit a few months later. BSOD happened quite frequent. During game and while watching simple browser videos. It even BSOD when just sitting on the desktop.

My specs are: CPU: I7 7700K Motherboard: Asus z270 Mark 1 RAM: 32GB Corsair Dominator Platinum 3000mhz GPU: EVGA FTW 1080ti PSU: EVGA 850W Supernova G2 OS Drive: Samsung 960 256gb I am running the ram at 2133. QVL show up that it has been tested.

I was having BSOD errors quite frequently. I managed to fix the error by removing 16gb of ram and going back to the original 16gb I had before upgrading to 32gb. I was wondering if you guys think it is faulty RAM or RAM slots? The BSOD was kind of random and 32gb would work off and on so I am unsure. Thanks for taking the time to read.

Okay so I stress tested my PC for about 2 hours with no issues. Booted up ghost recon and it froze. Get a BSOD with the error KMODE_EXECEPTION_NOT_HANDLED. Then I rebooted made it to the home screen and got another BSOD: PAGE_FAULT_IN_NONPAGED_AREA. I looked up the first one and it said it could be a driver issue. I also looked up if people had this issue with the controller wireless usb for windows xbox controller and they did. It does seem to be the last thing I bought for my computer and since has been acting up. Update: I uninstalled Malwarebytes, afterburner, rivatuner and I am not using the controller and its working okay.

Eclipse and Intellij are both good IDE's. They both offer syntax checking and completion so I would keep using Eclipse.

In my bios the targeted speed was already 2133 but the actual drop down menu to change the speed was set to auto. I don't know if will overclock automatically over this targeted speed but I set it to 2133 instead of auto.

Interesting. It makes sense. My board doesn't seem to stable with XMP enable either. I will change this and give it a day or two and report back if it happens or not. Thanks again!