ToroddWold
-
Posts
141 -
Joined
-
Last visited
Content Type
Forums
Status Updates
Blogs
Events
Gallery
Downloads
Store Home
Everything posted by ToroddWold
-
Thanks, it's been really hectic at work so I haven't had much time for PC building as for the final photos, they're on the way
-
I considered it, but I really don't want to have to drain my loop for a little while... (the block was released just as I was finishing my loop) not that the SSD needs cooling... I might get one later thanks The midplate was made using a 2mm alu plate and a 3mm white plexi plate (actually one 2mm and a 1mm glued togheter) both were laser cut at a local workshop. I can get the dimensions if you want, but they're not exact as I had to file some down to get it to fit
-
Case put back together almost ready to fill her up Working into the night started filling Side panel all done (finger print magnet)
-
case striped down and the panels sent for painting (excuse the mess) 420 rad back from painting small tease
-
Painting the plate Finally got the waterblocks and backplates seems like they have had problems getting them in stock since the launch of the 980ti (EK using titan x blocks for 980ti) I don't like that EK chose to go this route, the TITAN X engraving bothers me more than it should... :wacko: soon I can paint the case I carbon fiber wraped the MOBO plate I made, still need to make the wires for 2 GPUs and finish the midplate Still lots of work left.. but it sure is funn
-
Valknut plate just needs painting now
-
Just a small update on my progress with the mobo plate I still need to make a couple more cutouts for cables Marked up the screw holes and where the 24pin needs to go through drilling the holes Rough cutout The rubber grommet still fitts perfectly
-
From this: To this: Still a lot to be done.
-
I'm going with ''Valknut'' for the 5 1/4 bay plate (plate dimension is wrong) I've also startet working on a motherboard-tray cover plate, which should be done early next week
-
I'm expecting ~50c under load, and the heat won't transfer much to the surrounding air as heat is transfered and dissipated elswhere
-
it will be watercooled so I'm not woried
-
got something in my mail I think my mobo is officially full...
-
seems like EK won't release a 980 ti water block since it's the same as the TITAN X, this is going to drive my OCD crazy... :wacko: Think I'm going to use nickel & acrylic blocks and nickel plated backplates, should go better with the grey colour scheme.
-
I like the wrap idea better than painting it Linus style Thanks for the advice, I'll be sure to look into it
-
Thanks I don't have anything planned with the red on the mobo, the S-ATA connections should be the only place where you can see it easily when all the GPUs are in place. if you have any suggestions, pleas come with em'
-
The GPUs are here Starting to get cramped in the 900D Mah horse is done it fitts
-
did you make the midplate and mobo plate yourself or did you buy the pre-made ones?
-
-
currently running 1440P, but I'm going to get a ultra wide 1440 in the future. I've been using 2 7970 up until now they've served me well, even at 1440P
-
Titan Xs was in the mail, I'm sending them back in favour of 3x 980 ti... dat timing.... :wacko:
-
It's just a test fit, nothing was screwd in place. Just truing to see how it goes togheter
-
Making and testing the pump mount
-
Post Linus Memes Here! << -Original thread has returned
ToroddWold replied to COCOBYTES's topic in Off Topic
I've been reading that since they put up that sign... At least now I know I'm not the only one -
I hate when they have one pin spliting into two pins :angry: I had to make a Y cable from scratch 100% complete 24pin
