Jump to content
Search In
  • More options...
Find results that contain...
Find results in...

jclappers

Member
  • Content Count

    167
  • Joined

  • Last visited

Everything posted by jclappers

  1. jclappers

    Need Help for 23 inch display

    Preferably under $800 USD
  2. jclappers

    Pump Advice Needed

    Yup, go with a D5
  3. ive heard dirt is pretty good aswell
  4. jclappers

    My hate for Bitspower grows!

    I have never had any problems with bitspower parts and i would have used over $5000 dollars worth of parts on multiple builds (for work)
  5. jclappers

    H100i Fan Question

    Definitely exhaust
  6. What i want to know is if this loop would work effectively, desk will be about 1.5m wide for a bit of reference with the image Components i will be using are (open to change) - Ek Res X3 400, http://www.computerlounge.co.nz/components/componentview.asp?partid=18145 - Ek Coolstream RAD XTX480, http://www.computerlounge.co.nz/components/componentview.asp?partid=18798 - Ek D5 Vario X-Top, http://www.computerlounge.co.nz/components/componentview.asp?partid=20140 - 2x GTX 780 Things being cooled - CPU, GPU's, Crosschill Any help will be greatly appreciated
  7. jclappers

    [WIP] Snef's Sand of God

    I literaly clicked post as the pictures appeared
  8. jclappers

    Would this Loop Work

    a direct quote from Linus himself "I can't recommend a parallel configuration in many situations these days with head pressure being so much more important than max rate"
  9. jclappers

    [WIP] Snef's Sand of God

    I have subbed, you may begin posted this right as you posted the pics
  10. jclappers

    EK Fullcover waterblock

    i dont think they have a release date yet
  11. jclappers

    Would this Loop Work

    Yeah, its kind of complicated but it will essentially be a bitspower valve that leads under the desk
  12. jclappers

    Would this Loop Work

    The image is just the back section of the desk, it lowers down to a keyboard/mouse tray at the front Looking at raising the res' up a bit will be putting the pumps in series now, just have to figure out where to put them, also nice build same as above yup thanks for all the help, i will replan it quickly and come back with another version hopefully tomorrow
  13. You've inspired many people with this desk, myself included
  14. jclappers

    Corsair H80i Vs Phanteks PH-TC14PE

    get a phantek
  15. Ive been looking at Lutro but i want to buy in bulk and that does not seem to be the way to go, i will be using mdpc sleeving also 16AWG wire now unless someone gives me a good reason as to another size thanks all for the help and feel free to keep discussing your preferred methods etc
  16. http://www.amazon.com/Install-Bay-PWBK18500-Primary-Gauge/dp/B000GB0CQK/ref=sr_1_30?s=lamps-light&ie=UTF8&qid=1382239728&sr=1-30#productDetails Does anyone know if this wire will work for my 24pin etc PSU is a Corsair AX1200i if that matters Any help is much appreciated
  17. jclappers

    Sleeving: Discussion and Gallery

    @PBaines Are there any good places in NZ to get everything you need to make your own custom length cables, or do you just get yours from overseas
  18. Maybe hes going to put his impact with the bitspower water block in a bitfenix
  19. jclappers

    If your pump goes.....

    Very good advice right here
  20. jclappers

    Watercooling kits

    im not too sure about the 4930k but a 360 rad should do the trick
  21. jclappers

    Watercooling kits

    it says the three options all come with compression fittings so im a little confused as to why you are replacing them, unless you are getting some themed colour etc personal opinion, but get clear tubing and then a colored coolant Corsair's SP series would be better for the rad (better = more effective) H100i is cheaper and easier to configure kit a, b or c will give you lower temps and take a bit more effort to setup i personally run a h100i and i have never had any problems however i havent overclocked my cpu that much hope this helped
  22. jclappers

    Thoughts on this loop

    Thats always a big limitation and its even worse for us kiwi's over here, luckily the only thing i need to get from overseas is the fittings for my build
  23. yup mines 11.5 inches, and my h100i tubing is ...
  24. SUBBED, now i shall have a look at the sketchup
  25. jclappers

    One core is 10 degrees cooler

    haha i understand it now but before when all i new was "block and hammer method" with a cpu i was kinda worried
×