rellion

Hi guys, I am trying to work out the NW topology on this for now.... pardon me if im not too much of an expert. My intention is to achieve uniform coverage over 2 floors of a residential unit. The gear available to me is 1x AC68U, 2x Ubiquiti Unifi AC Lite and some misc NW switches. The entire house is pre-wired with Cat6 cabling. I have a few questions regarding setup, 1. I intend to run the APs all via POE so can I place the injector anywhere in the house as long as it's connected to a LAN port? After which I can just plug my AP into any available lan port around the house via POE? 2. I believe there are a few ways I can setup this. Option A: I can go with my Internet > AC68 (LAN out) through POE injector into wall port and then AP1, AP 2 will connect from the wall port as broadcast. Option B: If any of the APs does not have access to a wired wallport (eg. different floor) I can go with my Internet > AC68 (LAN out) connected via wire to Ubiquiti AP 1 and then AP 2 will use bridge mode to repeat the signal from AP 1. Is my assumption correct? Also, how should I deploy my APs for maximum effect? If I deploy only one AP below do you reckon the top floor will be able to get?

Grats jds!

Yes with the classifieds you can overvolt properly. Think performance beyond even most overclocked 780 Tis which are voltage locked

Sorry mate i just think u mightve lost the silicon lottery... That said i need 1.4v to get to 1425mhz

On water with an EK Block I know from personal experience in this forum even EVGA 780 Tis Superclocked will only pull 3200 or so even when overclocked stably

My card

This is what a 780 Classified can do @ 1425mhz

Well im not sure which 780s and Titans you are referring to but firsthand as an owner of 3 780s Asus DC2 780 = can get 1.212v via skynet bios. No unlocked voltage unless VGA hotwire hardmod. Confirmed by Ed aka OccamRazor from Skynet. Palit Jetstream 780 = 1.212v through skynet bios flash too. No further unlocks EVGA Classy 780 = 1.212v through skynet bios. Up to 1.5v via Classified Tool Im not sure how you would get > 1.212v on an Asus or similarly locked card. Would you be able to enlighten?

If you include soldering and hard mod then of course. Very very very few users will go to such extremes where they have to remove caps and solder the pcb. We're talking bout normal softmod voltage unlocks

No man. They can only be unlocked to 1.212v but beyond which is what u need for real speed (1.4vs or so) can only be achieved by classified and i think lightnings. I have this triple checked by ed (occamrazor) from skynet

No man! Save the money your sc is wayyyy overpowered for current games A custom loop is alot of work and take it from my experience... Dont watercool a voltage locked card... GPU boost has very limited perf bins even putting it under water compared to acx might not make any diff

Only get a classy if youre willing to flash the bios and overvolt it. Otherwise youd be better off keeping your sc

Jds Your score of 3.2k at valley is no slouch but like i showed u previously my 780 non ti classy can do over 3.5k... So if u were to get a 780 ti classy youd be looking at 3.7-3.8k

http://i105.photobucket.com/albums/m231/vagpwner/photo8.jpg 290 for price but if u want real performance get a 780. The score above was with a single 780 classy To put it in perspective a 290 even when overclocked would push around 2.6k or so only

Depends? On the voltage controller you mean?