FuegoFett

We’re a small business managing multi family apartment complexes and we’re looking for solutions similar to the UniFi dream machine on our smaller properties. We need a single pane solution so we have one cloud panel for all of our sites similar to the UniFi cloud controller. We want it to be WiFi, security gateway and switching also. I’ve been trying to search and find anything comparable for the price or cheaper. Any suggestions?

I have the top rear fan as exhaust. top front fan as intake. I have not put in any fans in the rea as of yet but would make them exhaust if I did. I have corsair LL120 on all my radiators as I did before in the same configuration. the flow is fine, I have test with vapor. It pushes plenty out of the front rad. Could air pockets or bubbles cause this?

The front radiator is laying flat with pushing down. The side rear radiator is up and down with fans set to intake.

All the BIOS settings are the same. Intel speed boost is enabled. its all on auto. 4.7 all cores is what I am using. and before it worked like a charm.

one laying flat and one up and down with the ports at the bottom of the case. Before they were the same one up top and trhe other up and down except the fill ports were at the top.

That is how it stays. And thats the temps.

I recently changed cases and changed up my custom loop. I am still using the same pump/res 2 radiators gpu block and mono block. I use hardline in the front of the case. I added some passthroughs and flextube on the back of the case to go to one of my radiator and back to the pump. I am seeing temps 10-20 degrees higher than they were before. any idea why this might be happening? there is good contact on the processor and same fan setup and OC as before. Before I changed case and added the soft tubing I was idling 24-28c and under full load I would hover 55-65c. Now I idle 40c and under simple game use i hover 45-65c and full load I hit 70-80c. GPU temps are normal 24c idle and 35-40c under use. I can not figure this out. I replace my mobo and the monoblock with the same models. My ambient temps are the same as well. I changed from a Lian Li 011 Dynamic to a Thermaltake Level 20 HT EK 150 pump res combo EK Hardline PETG in front EK Soft Tubing in back Bitspower Fittings for soft tube EK fittings in front EK Cooling Fluid EK slim 360 EK 360 EK z390 meg ace monoblock EK rtx 2080 gaming trio gpu block 9900k msi 2080 gaming x trio [4:54 PM]

If I’m running a lian li 011 dynamic with 2 360mm rads for my hardline configuration with mono block cpu cooler and gpu cooler. Would it be a bad idea to run all exhaust fans and no intake?

It is only 6 feet. I have noticed that if I leave the display off it wont mess up until i move a window to it for a while. It is intermittent.

Not yet. Why would that matter? After upgrading to new cables it slowed down how often it happens

I’m using top notch hdmi 2.0 cables.

Neither of those options worked.

I have an MSI RTX 2080 Gaming X Trio. Using three monitors. One is a 32 inch vizio 1080p 60hz tv. I’ve tried using hdmi, hdmi to display port, and hdmi to type c cables. No matter what cable I use every once in a while the tv will black out and after after 5-10 seconds come back like I unplugged the cable and plugged it back in. I’ve used the same cables on my monitors and blu Ray players and such. It only happens when the tv plugs into the computer. I tried disabling dynamic super resolution in the nvidia control panel. I tried running the tv in other resolutions. Does anyone have any ideas?

Gaming, scripting, network security and streaming.

Thanks. So I should get all X4 m.2 or with multiplle, would it be better to run OS off an X4 and the other 2 on x1?