slider_aus

i sadly wont have the ability to wall mount it

well i would prefer something around the size of a mid tower but can go bigger i also have the gigabyte 280mm aio cooler wich with its stupid but cool looking fans is a pain in the ass to fit. and my motherbord i think is atx "gigabyte aurus x570 pro wifi" and i definatly would perfer a enclosed case with verticle mounting like the p3 you suggested (i have a very furry dog)

what other information would be helpfull?

i have a aurus xstream 2080 ti and i would like to mount it verticly so i can see its pretty fan lights. im not sure what case to get because im oncerned of how wide the gpu is with its cooler and how close it may get to the side glass panel from were i have seen most verticle mounts are in cases like the corsair 680X wile also bearing in mind i have a pcie capture card. i also prefer to have an inclosed case but can be flexible. my main concern is keeping good airflow to it. any advice and recomendations would be appreciated.

no im afraid i have not. however i did find a fix for me turning off multiple displays in windows so only my fi27q-p is displaying an image, i can then launch OSD sidekick and it will detect my monitor and i can go back and re-enable multiple displays, and osd sidekick will work as normal. until you reset my pc of course

i think i originaly put this in the wrong spot so ill try again >.< i have a aorus FI27q-P pared with my FI27Q, osd sidekick detects the non -p monitor but not the -p "yes the monitor usb cable is plugged in'' the -p is the newer of the monitors and was just using the non p version for a while and the sidekick software worked fine. plugging in the new -p and the software will not detect it, usb passthrew functionality works just fine though. i have tried reinstalling the software, running it with just the -p plugged in, contacting gigabyte, (my exsperiance with gigabyte support will be a thread on its own) my windows install is very fresh aswell being only a few months old at version 2004 build 19041.450

i have the aorus FI27q-P pared with my FI27Q, osd sidekick detects the non -p monitor but not the -p "yes the monitor usb cable is plugged in'' the -p is the newer of the monitors and was just using the non p version for a while and the sidekick software worked fine. plugging in the new -p and the software will not detect it, usb passthrew functionality works just fine though. i have tried reinstalling the software, running it with just the -p plugged in, contacting gigabyte, (my exsperiance with gigabyte support will be a thread on its own) my windows install is very fresh aswell being only a few months old at version 2004 build 19041.450

ok i can undrstand that but in ryzen master cores 1-3 are on ccx-0 cores 4-6 are on ccx-1 and both of those are on ccd-0 then there is ccd-1 with ccx-0 with 7-9 and ccx-1 with 10-12. is there any way to confirm what thread belongs to what core

hay ppl i have looked everywhere to try and figure this out but could not find an answer i want to know how to figure out when looking at the performance tab of the task manager what "cpu" belongs to what core and ccx on my ryzen 9 3900x. i want to know this so i can better set my cpu affinity.

hmm i have entered the timing manually and bumped voltage from 1.35 to 1.37 from the stock xmp profil, maybe i should just slam it too 1.4?

I recently got a kit of CORSAIR Vengeance RGB PRO DDR4 16 GB 3200 MHz CL16 (16-18-18-36) in my Gigabyte B450 AORUS Pro and Ryzen 7 2700X, and have had issues of instability with the xmp profile and can only get it stable'ish buy raising the voltage. my question is in my motherboard manual it says it supports speeds up to 2933, 2667, 2400, and 2133, is this why its not stable? because i have seen reviews were ppl are using high speed ram on the b450 chipsets no problem, or is my ram just faulty?

so after running the ram at 1.37v at xmp settings it has ran perfectly sense the 23rd but all of a sudden its crashing games again.

there is only one im trying again with manully entering the clock and timing and bumped up the voltage to 1.370V, hasant crashed yet

my manual foor my motherbord says it oonly supports up to 2933 mhz is this really an issue?

ill doo that again then but i have also had a game crash already

ok all updated. and i have the kit back into the system and the xmp profile enabled, guess ill play some games and see if it falls flat on its face

doont worry im uing the stable kit

i got to F32 will i need to run that ECFW tool again? or is it fine?

i dont understand how to update it wile in windows

i do still have it but i cant even get it to flash yet

im having trouble getting the qflash utility to detect my thumbdrive i exstracted the bios to the thumbdrive but it just wont pick it up in the utility yet i can see it apearing in the bois itself

now i have never flashed a bios before do i start at the first bios and work my way up or can i just update to the latest?

ok i ran the software and it reset my pc

what is ecfw?

i have never flashed the motherboard and im not sure if i have the latest chipset drivers (i just pdated to the latest chipset drivers)