6700k overclock help [ WIP, Stable But...... ]

[vESP]

3 minutes ago, legacy99 said:

1.4v is the community recommended voltage to run for 24/7 operations. You can push it up higher, some say up to 1.45, but its not recommended to leave it there for 24/7 usage. 

Yea. I leave the system on for as long as I'm awake since it's in my bedroom.

 

Maybe 14 hours half at idle since I'm either watching anime or youtube.

[vESP]

22 minutes ago, legacy99 said:

Thats fine. 

 

http://ark.intel.com/products/88195/Intel-Core-i7-6700K-Processor-8M-Cache-up-to-4_20-GHz

 

This is the official spec sheet of intel. Intel lists it can go up to 1.52v. You are find with continuing to bump it up. 

 

1.4v is the community recommended voltage to run for 24/7 operations. You can push it up higher, some say up to 1.45, but its not recommended to leave it there for 24/7 usage. 

 ive passed the standard on 10 pass, @ 1.380v

[vESP]

10 minutes ago, vESP said:

 ive passed the standard on 10 pass, @ 1.380v

had 2 IBT induced freezes on HIGH where i had to hard power my system down,

 

running at 1.395v @ 4.7ghz.

 

Starting standard IBT......

 

[vESP]

1 minute ago, vESP said:

 

 10 pass IBT

Starting standard IBT......

 

Update:  PASSED

 

starting high IBT:

[vESP]

Update: Passed.

 

screen has flicked to black after every pass wih pointer and blue orb no crashing or hard freezing.

 

Starting 20 PASS hard IBT

[vESP]

14 minutes ago, vESP said:

Update: Passed.

 

screen has flicked to black after every pass wih pointer and blue orb no crashing or hard freezing.

 

Starting 20 PASS hard IBT

update: PAssed 

 

so far stable

Edited August 10, 2016 by vESP
added screenshot

[vESP]

Update and some worry so i need some help!

 i had to volt up to 1.480v [ bios pics provided |Edit]

 

Stable on realbench single run benchmark, had been BSOD etc before i hit 1.48 same on IBT

 

Stable on IBT HIGH 20 pass.

but my temps got higher then they did on realbench when i use IBT see the pics they are in order of temps and stages.

the 2 left cores [ 1nad 2 i think ] hit 90+ cel leaving 10cel before TJ MAX [ not seen in screen as taken after test ]

cores 2 left cores [ 3 and 4 i think  ] never hit 90 at all and mostly 85- cel

 

do i lower voltage to the point i BSOD etc or up my h100i gtx fans as they are at about 1100rpm for my own DB comfort im running the pump on performance mode hopefully that might speed up the water to plate cycle..  

although i did receive a offer on ebay for my h100i gtx so i might upgrade to a bigger rad AIO as i dont think i can safely use a D15 from noctura without TJ max and burning a hole in the earth.

Edited August 10, 2016 by vESP
Added bios voltage images

[vESP]

Sad Panda. 

Temps etc after 3d mark firestrike stress and 2 runs of tom clancy the division on 1440p 144hz max settings but low shadows.

 

EDIT:  Idle temps with 4 and then 0 programs active [ not including the tasks hiding in the background only minimised ]

 

 

 

EDIT 2X:

 

Changed cpu fan speed to be adjusting to temps of cpu so tj Max is always 20c off before 100℅ fan speed.   *Fyi.  System fan 3 is rad fan speed, running off mb rather then Corsair link control.*

 

May upgrade to a 380mm aio or d15 if temps would work safer then current.

 

Still working on voltageXtemp. Waiting on forum advice

 

 

EDIT 3X:

 

custom fan curve seems to run good may adjust to allow a lessor jump to 100% at 80celius. but kept cores cooler at 100% then they were originally underload.   * Temps in picture is from 3 runs of IBT at 10x standard 10x high 2x very high followed by 1min of realbench stress test*

EDIT4X:

apon checking this post after last edit, the Bios fan curve is the same as the one in the image above. i do not know why MSI commander is showing a different one.