Project Iced Blood - Mayhems/Primochill Sponsored. COMPLETE 15/02/16

[stealth80]

Simple solution: use colored/tinted tubing and clear coolant.

 

 

Wont really help my 4 clear blocks and 2x radiators lol 

[Wolf_Lbh]

Wont really help my 4 clear blocks and 2x radiators lol 

(Tinted saran wrap)

[stealth80]

 

(Tinted saran wrap)

 

 

 

An idea, but I ain't putting that on my blocks lol. Like I said I will probably just use X1 which doesn't seem to suffer the issues that Pastel does

 

Thanks anyway 

[Derpologist]

An idea, but I ain't putting that on my blocks lol. Like I said I will probably just use X1 which doesn't seem to suffer the issues that Pastel does

 

Thanks anyway 

Good plan mate.

Can't wait to see the finished build!

[stealth80]

Looks like I may have another sponsor onboard, just need to wait confirmation! 

[stealth80]

Confirmation today that Primochill have kindly offered to sponsor my venture into rigid tubing!!

 

Thanks Again

 

[stealth80]

Parts should be shipped today 

[Silver47]

Wow Dude this is some nice work! Friggin' huge case and radiators. Would you mind posting temps when your done building?

[stealth80]

55 minutes ago, black0utm1rage said:

Wow Dude this is some nice work! Friggin' huge case and radiators. Would you mind posting temps when your done building?

The rig is up and running at the moment with flex tubing. Idle temps are around 28C for CPU and 22C for GPUs.

 

Gaming load temps around 37C on the CPU and 47C on GPUs

[stealth80]

Hurray, Parcelforce finally picked up my shipment from UK customs, a nice little box of modding kit for this build!

 

Thanks to Primochill for providing the following products:

 

 

So 2x Flow Meters, A Rigid Bender, a whole bunch of the new Primochill RSX fittings and a whole bunch of Primochill 12/10mm PETG tubing

 

 

Rigid Bender, seems like a nice piece of kit, used it this evening and it definitely works, good job Primochill! 

 

 

 

 

2x Flow Meters - During the last 6 months or so my rig has been pretty damn quiet, too quiet. At times I wasn't sure if the pumps were actually running, so these should hopefully aid that issue:

 

I really like the amount of different tubing configs you can use with these:

 

 

Next up are the 2x sets of Primochill RSX rigid tubing fittings. These are very new and they seem like a massive improvement over the Monsoon fittings I was using previously

 

Particularly liked the packaging!

 

 

I eventually ended up spending around 6 hours making some progress tonight. Most of that time was actually used to strip all the radiators and tubing out and flushing all the old coolant out and cleaning the CPU/Chipset blocks.

 

I made a few bends and got to grips with using the Rigid Bender, which is pretty useful!

 

 

 

 

[stealth80]

Some more work done yesterday prior to a heavy night on the town!

 

First piece of bending today was a pain in the ass, trying to get the bends correct for the pump outlet that drops below the partition wall and into the 240mm radiator

 

 

 

 

Once that one was done (5 attempts later!!!)  it was pretty much plain sailing to complete the CPU loop and most of the GPU loop

 

 

I changed the old GPU layout a little to allow for cleaner looking bends and adding the Flow Meter

 

 

Then onto some leak checking for the CPU loop, early signs all good

 

[stealth80]

Disaster (maybe averted)

 

Finally finished the loop and did some leak checking and all seemed good ....

Had a leak from the Parallel Terminal (only part not disturbed!) which leaked in between the 2x GPU's where I can't see ....

Turned PC on, pc restarted twice then I switched off at mains and eventually found the issue. On the plus side both GPU's are fine as I've tested those in another rig and I've dried the motherboard out and blown it through with compressed air. Will wait till tomorrow to test the board, but fingers crossed ...

[stealth80]

She LIVES!!!

 

I'm not sure how, liquid went on the board between the PCIE slots and power was on the board.... Guess RoG stuff can be decent!

 

Ill add some photos of the finished item later today, just gotta flush and bleed it

[stealth80]

Update 15/02/16

 

So after the panic last night I figured whilst I have the loops drained I would swap all the Fittings around, aka white on red and red on white, I suspected it would look much better.

 

Did all those last night and rebuilt the loops and waited until this morning to power up the PC.

 

So back to leak checking!! (although I was pretty certain there were no leaks this time!)

 

 

 

 

I left it running like that a little whilst bleeding the loops and leak checking all the fittings and especially that Parallel Terminal, had half of a toilet roll stuffed between those gpus today!!

 

 

 

 

 

[stealth80]

So it's now complete, it works and more good news, my RMA replacement for my Asus RoG Swift Gsync monitor shall arrive tomorrow!!

 

I decided to do a little stress testing whilst finishing off the flushing and making 100% sure there is no leaks, AIDA 64 full stress test without any issues, so I guess I really did get lucky with that leak!

 

I followed the AIDA64 with a run of 3dmark Firestrike on default settings, just to see what kind of scores I could get and how the temps are:

 

This was the second run, I'm pretty sure I can get 1500mhz on these cards and I know the CPU does 4.9ghz. This one was ran at 1468/1856 on the cards and the CPU at 4.8ghz

 

http://www.3dmark.com/fs/7571570

 

Graphics score 25816, I'm plenty happy with that, more impressive were the temps:

 

 

Next weekend I'm gonna try for 5ghz on the CPU and 1500/2000 on the cards, probably going to need a bios flash, but I will see how I feel at the time.

 

Onto the final pics, thanks for reading so far!

 

 

 

 

 

 

The RoG front base still isn't working as my man that is lengthening my loom is out of the country with work, that will be added in a couple of months

 

 

 

 

 

 

 

 

[stealth80]

On ‎06‎/‎01‎/‎2016 at 1:01 PM, BurnerMC said:

Yes please do hard line tubing

 

You requested, I answered

[stealth80]

I decided that (should have done this when I went SLI) the GPU's were kicking out a lot more heat than the CPU loops, so I stripped half of each loop and spent around 4 hours flushing and cleaning the 240mm rad and added it to the GPU loop, temps dropped 2 - 3C which aint too bad and now I get a foot heater whilst i'm gaming!!

 

 

 

 

 

[GDRRiley]

nice work looks very good. 

[Derpologist]

Damn, that looks great

[Str8f4c3]

Beautiful, and I am glad that someone is using white/red color scheme!

[stealth80]

6 hours ago, Str8f4c3 said:

Beautiful, and I am glad that someone is using white/red color scheme!

Thanks, just happens to be the colours of my football team lol!

[LordDecapo]

Love this build! Glad you ended up changing to hardline tubes. Looks soo good

[MIXFUSED]

Hey I know this is old, but nice build!!!

[stealth80]

Thanks!

[stealth80]

Now with improved Palit 1080 GTX Gamerock Premium!!