Jump to content
Search In
  • More options...
Find results that contain...
Find results in...

I just switched to an AMD system:

 

5900x

Aorus x570 master

G.skill Trident 32g (2 2x8) 4000mhz kit

Asus 3070 dual 8g

SS 750w psu

H150i capellix

011 dyanic case 

With 9 unifan. 

 

Setup of fans /aio

Aio top push/pull exhaust

Bottom/side intake

 

Problem: 

Unstable

Im really new to amd, literallyy 1st tjme

 

My idle temps at 49-60

Load at highest 93

 

I fiddled with PBO CO, set to neg at 20 offset but unstable. Also used amd master, used creator, then auto OC, would be stable for a few hours, can even do 15 min prime95. With ok r23 scores. MC 22104

 

But then during gaming, would crash with esports titles (PUBG/Apex/underlords/dota)

Apex and pubg at low settings 1440 170hz

 

Just today i tried to manual oc on amd master, set to 4500mhz at 1.3v. 

Got lower temps idle 49-55, then load at most 91, fans still ramp up tho. 

 

Anyhelp on theses, i just want lower temps with decent mhz, and hopefully a less noisy system. 

 

Hope anyone can help  

 

Thanks! (From philippines)

 

Link to post
Share on other sites
4 minutes ago, Rey Christopher Torres said:

crash

Does it bluescreen or just blackout? 

 

6 minutes ago, Rey Christopher Torres said:

G.skill Trident 32g (2 2x8) 4000mhz kit

Does your infinity fabric clock reach 2000mhz? You'd want to run ram and IF clocks 1:1, so for 4000mhz ddr ram speed you want 2000mhz on your IF. Assuming you enabled docp. 

 

 

Also: is the system stable when you do not oc (pbo or else)? 

My Rig / Buildlogs:  ❄️ SNOWFLAKE ❄️ FROSTBITE ❄️

CPU: Ryzen 5 3600   Cooler: Corsair H115i Platinum   RAM: Corsair Vengence RGB Pro 16GB @3200   Mobo: Asus Prime X470 Pro

Graphics Card: Gigabyte Aorus 2080super Waterforce    Case: Corsair 500D   PSU: Corsair HX850i

Storage: 500GB Crucial P1 NVMe SSD, 1TB Crucial P1 NVMe SSD, 2x 1TB SATA SSD

Displays: AOC CQ32G1 32" 2560x1440, Acer XB280HK 28.0" 3840x2160 60 Hz, Medion MD20850 24" 2560x1440

 

 

Link to post
Share on other sites
2 minutes ago, LauriHimself said:

Does it bluescreen or just blackout? 

 

Does your infinity fabric clock reach 2000mhz? You'd want to run ram and IF clocks 1:1, so for 4000mhz ddr ram speed you want 2000mhz on your IF. Assuming you enabled docp. 

 

 

Also: is the system stable when you do not oc (pbo or else)? 

I got twice bsod, but mostly, blackout and restart. Sometimes will freeze or crash, but not windows. 

 

I think i have to set IF to 2000mhz. Will def check that. 

 

Im on duty right now. Most of the help i'll get here, i will be able to implement tom.  

 

Any more tips? Im really worried bout my idle temps. Are they really that high? 

Link to post
Share on other sites

Is it stable in stock config?

Main: AMD Ryzen 7 2700X, Nvidia GTX 1080 Ti, 16 GB 3200 MHz DDR4 Fedora 35 x86_64

Secondary: Intel Xeon W3680, AMD Radeon HD 6950, 24 GB 1333 MHz DDR3 Windows 10 Home x86_64

Server: 2x Intel Xeon X5670, 72 GB 1333 MHz DDR3-R Ubuntu Server 20.04.1 LTS x86_64

Home Laptop: Intel Core i5-L16G7, 8 GB 4267 MHz LPDDR4x Windows 10 Home x86_64

Work Laptop: Intel Core i7-10510U, NVIDIA Quadro P520, 8 GB 2667 MHz DDR4 Windows 10 Pro x86_64

Link to post
Share on other sites
5 minutes ago, Rey Christopher Torres said:

Im really worried bout my idle temps

high idle temps are pretty common on ryzen 5000

did you have pbo enabled when reaching those temps?

My Rig / Buildlogs:  ❄️ SNOWFLAKE ❄️ FROSTBITE ❄️

CPU: Ryzen 5 3600   Cooler: Corsair H115i Platinum   RAM: Corsair Vengence RGB Pro 16GB @3200   Mobo: Asus Prime X470 Pro

Graphics Card: Gigabyte Aorus 2080super Waterforce    Case: Corsair 500D   PSU: Corsair HX850i

Storage: 500GB Crucial P1 NVMe SSD, 1TB Crucial P1 NVMe SSD, 2x 1TB SATA SSD

Displays: AOC CQ32G1 32" 2560x1440, Acer XB280HK 28.0" 3840x2160 60 Hz, Medion MD20850 24" 2560x1440

 

 

Link to post
Share on other sites
11 minutes ago, svmlegacy said:

Is it stable in stock config?

Im really not sure.. will try it tomorrow.. but i guess mostly but i do remember i had a blackout like twice, 

Link to post
Share on other sites
10 minutes ago, LauriHimself said:

high idle temps are pretty common on ryzen 5000

did you have pbo enabled when reaching those temps?

Yeah i've read that. But what are the accepted ones. Im pretty sure mine are quite high. Not sure if its due that im here in ph... plus, the fans always ramps up when i set it to balanced/pwm..  if i put it to quiet, it gets more unstable... 

Link to post
Share on other sites

Cooling is important. The memory too. 

 

Are you running the XMP 4000 profile or something else?

- If it ain't broken, don't fix it! - - Your post codes and beep codes in the drop down below -

Spoiler

 

 

Link to post
Share on other sites
Just now, Rey Christopher Torres said:

Not sure if its due that im here in ph...

what are your room temps like there?

My Rig / Buildlogs:  ❄️ SNOWFLAKE ❄️ FROSTBITE ❄️

CPU: Ryzen 5 3600   Cooler: Corsair H115i Platinum   RAM: Corsair Vengence RGB Pro 16GB @3200   Mobo: Asus Prime X470 Pro

Graphics Card: Gigabyte Aorus 2080super Waterforce    Case: Corsair 500D   PSU: Corsair HX850i

Storage: 500GB Crucial P1 NVMe SSD, 1TB Crucial P1 NVMe SSD, 2x 1TB SATA SSD

Displays: AOC CQ32G1 32" 2560x1440, Acer XB280HK 28.0" 3840x2160 60 Hz, Medion MD20850 24" 2560x1440

 

 

Link to post
Share on other sites

Would really help if anyone can share or guide me on how they did it or what exactly to do. Dont know shit on this amd platform.  Sorry

Link to post
Share on other sites
1 minute ago, ShrimpBrime said:

Cooling is important. The memory too. 

 

Are you running the XMP 4000 profile or something else?

Xmp profile

 

Re cooling, thats why i switched to the capellix 360

 

Room temps i think at most 25c since it raining here.. 

Link to post
Share on other sites
17 minutes ago, Rey Christopher Torres said:

Xmp profile

 

Re cooling, thats why i switched to the capellix 360

 

Room temps i think at most 25c since it raining here.. 

Use HWInfo64 and monitor the memory temps while testing at load. 

 

Some chips IF don't like running 4000mhz. As a result, you can increase CPU SOC voltage, but this will increase cpu thermals.

 

Maybe drop the memory frequency to 3800 with the current voltage settings and see if it's more stable. Keep the 1:1 link for now.

 

Alternatively, you could run 1:2 keep the memory speed, but will cut IF frequency in half. This is not always desirable, but can help diagnose memory stability, so F the nay sayers. They just don't know how to diag....lol

- If it ain't broken, don't fix it! - - Your post codes and beep codes in the drop down below -

Spoiler

 

 

Link to post
Share on other sites

1:2 isn’t worth it unless you can run your ram at 4200 minimum. You gotta get your IF back up once you unlink it.

AMD R9 5900X @ + 150MHz | Thermalright Frost Commander 140/NF-A14 iPPC/SYY-157
Asus Strix B550-F Gaming | 4x8GB G.Skill Trident Z Mix @ 1866MHz 14-14-14-34 1T 1.5v
EVGA RTX 3070Ti FTW3 Ultra @ 2085/1212MHz | WD SN750 500GB, 1000GB, 545S 256GB
Seasonic Prime GX-750 | Fractal Design Meshify C | TY-143, TL-D14X, TL-C12 Pro, NF-F12 iPPC

Link to post
Share on other sites
17 minutes ago, ShrimpBrime said:

Use HWInfo64 and monitor the memory temps while testing at load. 

 

Some chips IF don't like running 4000mhz. As a result, you can increase CPU SOC voltage, but this will increase cpu thermals.

 

Maybe drop the memory frequency to 3800 with the current voltage settings and see if it's more stable. Keep the 1:1 link for now.

 

Alternatively, you could run 1:2 keep the memory speed, but will cut IF frequency in half. This is not always desirable, but can help diagnose memory stability, so F the nay sayers. They just don't know how to diag....lol

Memory 1:1 means divide by half right? If 4000mhz, then IF at 2000? Or 3800 then1900?

Link to post
Share on other sites

Yes.

AMD R9 5900X @ + 150MHz | Thermalright Frost Commander 140/NF-A14 iPPC/SYY-157
Asus Strix B550-F Gaming | 4x8GB G.Skill Trident Z Mix @ 1866MHz 14-14-14-34 1T 1.5v
EVGA RTX 3070Ti FTW3 Ultra @ 2085/1212MHz | WD SN750 500GB, 1000GB, 545S 256GB
Seasonic Prime GX-750 | Fractal Design Meshify C | TY-143, TL-D14X, TL-C12 Pro, NF-F12 iPPC

Link to post
Share on other sites
51 minutes ago, Rey Christopher Torres said:

Memory 1:1 means divide by half right? If 4000mhz, then IF at 2000? Or 3800 then1900?

Right. Reduction of ratio, or "unlink the IF" from the memory strap, it would be 4000/2000 memclk and 2000/1000 Infinity Fabric - IFclk. 

 

With that you could OC the memory past the XMP frequency. 200mhz should be doable IMO.

- If it ain't broken, don't fix it! - - Your post codes and beep codes in the drop down below -

Spoiler

 

 

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×