SaHaRzZz got a reaction from thrasher_565 in Looking for an upgrade from an H710
So my CPU temps are never low for some reason, I swapped to a new motherboard, downgraded to an 3600 from an 3900x, and even swapped from an X62 to an H150i, and temps are still.. not the best, 50c at idle.
which makes sense because my setup is crap, I'll explain why.
I have the H710, with a 2080ti + Kraken G12 & X62, mounted at the front, with push&pull configurations, 48-50c at load with the GPU, I'm very pleased with that.
After that, the CPU, which is now a 3600 + H150i, mounted at the top, with push configuration (can't really do pull on that one), 50c idle and around 75~ish at load.
The H150i liquid temp at idle is 40, which is pretty high for idle, and probably is because of the front intake giving hot air.
And of course I have a rear 140mm fan, BTW all of my fans are pretty good, Corsair ml pro series & noctua, only the H150i has the stock 1500rpm ml120 lies edition fans.
What I thing I need is a new case, because I see everyone bashing the H710 for poor airflow capabilities, and if that is what will bring me to sub 40 idle degrees, then that's what I want.
I'm completely open to hear case suggestions!
SaHaRzZz got a reaction from ShrimpBrime in Can't get a proper boost from my 3900x?
I got a great deal for the parts and that's why I took the gen1 board with the gen3 cpu,
i'll OC my ram to 3800 cl16 and the IF to 1900 or at least try to, with the dram calculator ^^
Thank you very much!
you and @DildorTheDecent have helped me a lot !
SaHaRzZz reacted to ShrimpBrime in Can't get a proper boost from my 3900x?
Ryzen 3000 series processors have a throttle point of 95c. Your 84c, has a little headroom left.
Want to run IF and memory clocks linked as high as possible. 3800mhz is a goal. In most cases IF won't do 2000mhz, so need to unlink at this frequency.
Tweaking SenseMi technology to your particular rig takes time. Not so cut and dry as manual overclocking is. There's quite a few settings to play with "boosting" clocks if you will, again, takes time to tweak it all.
Are you good? Well yea aside from running a Gen 1 board with a Gen 3 cpu.... I think you're doing fine.
The cooler you run that Ryzen Cpu the better because it will sustain boost clocks for a longer duration. My Ryzen chip is default all core boost of 4ghz, 4350mhz single core boosts. If it runs hot enough, the all core boost will throttle to 3.9ghz and I usually see this once I hit 85-90c as this is where my throttle point is.
High temp cpu alarm is at 70c. At this temp, the stock fan profile will put the fan to 100%. This says something doesn't it? Why did AMD boost clocks and voltages past this temp from stock?? Well, to eek out every last ounce of performance leaving absolutely no headroom for manual overclocking.
SaHaRzZz reacted to Hyoung13725 in Looking for a PC case under 150$
I was actually considering the same lion li case at first until I started digging & watching videos like Gamers Nexus, Hardware Canucks, they show cpu & gpu real temps under load & at idle. I didn't realize how in depth a case review could go. So after hours and hours of watching reading you name it lol I just finished my Ryzen 3rd gen pc & I would HIGHLY suggest the Cooler Master here's a link of one of the reviews that helped with my decision. I searched for hours to not only find a case that was aesthetically pleasing, but also one that is going to give me awesome airflow (at the time, I was willing to sacrifice a "prettier case" for more airflow, but with this case I didn't have to at all.
It is ridiculously quiet, so much that I cannot even hear it under load all while not wearing any headphones! Here's the specs for it as well:
Front Panel: Mesh, Acrylic & Plastic
Top Panel: Steel & Plastic
Left Side Panel: Tempered Glass
Right Side Panel: Steel
-Dimensions (LxWxH) Excl. Panels: 450 x 220 x 445mm
-Incl. Panels: 525 x 228 x 502mm
-Motherboard Support ATX, Micro-ATX, Mini-ITX
-Expansion Slots 7
-5.25" Drive Bays No
-Combo 3.5" / 2.5" Drive Bays 2
-2.5" SSD Drive Bays 2
-I/O Port Power-LED Color: White
-HDD-LED Color: White
-USB-Ports: 2x USB 2.0, 2x USB 3.0
-Audio In / Out: Yes
-Reset Switch: Yes
-RGB Control Onboard button on the RGB Controller or via the Reset Switch (1x 1-to-3 RGB Splitter Cable Included)
-Pre-installed Fan(s) - Top N/A
-Pre-installed Fan(s) - Front 2x 200mm RGB Fan
-Pre-installed Fan(s) - Rear 1x 120mm (Black) Fan
-Pre-installed Fan(s) - Bottom N/A
-Fan Support - Top 2 x 120mm / 2 x 140mm / 1 x 200mm
-Fan Support - Front 3 x 120mm / 2 x 140mm / 2 x 200mm
-Fan Support - Rear 1 x 120mm
-Fan Support - Bottom N/A
-Radiator Support - Top 120 / 140 / 240mm
-Radiator Support - Front 120 / 140 / 200 / 240 / 280 / 360mm
-Radiator Support - Rear 120mm
-Radiator Support - Bottom N/A
-Clearance - CPU Cooler 167mm / 6.5"
-Clearance - PSU 180mm / 7.1"
-Clearance - GFX 410mm / 16.1"
-Cable Routing - Behind Motherboard Tray 30mm
-Dust Filters Top, Front, Bottom
-Power Supply Support Bottom Mount, ATX
(Also, one thing I didn't realize is if you can find a case with bigger fans or the ability to even install bigger (140mm to 200mm size) the quieter your pc will run as well)
Hope that helps! - Oh & the price of this case at Micro Center was $119 but Amazon has it for $109 I believe still.
SaHaRzZz got a reaction from Hyoung13725 in Looking for a PC case under 150$
I just can't understand which one is better and in what
I'm looking for a PC case for a standard ATX board, x370 hero 6, and it will contain two NZXT X62, so I'm gonna have to fit dual 280mm radiators in there,
and.. well cable management, 2 2.5" SSDs, commander pro and things like that behind the scenes.
Do you guys have any recommendations? Ive been looking at the "lian li pc-o11 dynamic", it looks good but I am really not sure if it is or if there's a better choise.
SaHaRzZz got a reaction from Lurick in Devices remembering network by what?
That's actually awesome to hear, that means that it could work!
I'll try it out, thank you!
It is a router as far as I know, with a different subnet and everything, specifically for my smart devices.
All I needed to do is to make sure that I can switch to another one without issues coming from the smart devices.
I think that is it! thank you both !
SaHaRzZz reacted to akio123008 in Devices remembering network by what?
Personally I'm running a dual AP setup (no mesh or 802.11x) with two regular APs that have the same SSID/password combination and are running on different channels. When I walk around the house with my phone, it will constantly switch to whichever AP has the best signal and on most devices this actually works really well. Some devices act weirdly every now and then, they then refuse to reconnect (they're sticky) or they simply connect to the wrong AP, but this rarely happens, and even when it does, manually reconnecting always fixes it. So in your situation, where the old AP is taken down and then replaced with one that uses the same SSID, I don't think there will be any difficulties.
Edit: also please stop calling an access point a router.
SaHaRzZz reacted to paddy-stone in Devices remembering network by what?
yes, in most cases they will just connect as before if you use same SSID and password. This is really handy for so called smart devices, where the setup is complicated unnecessarily... yes echo I'm talking about you you bitch! ?
When I bought my last AP/mesh system I was going to re-do everything... so did, and then the bloody echo dots we have wouldn't have it, so after wasting like 2 hours trying to get the effing echos and stuff to work... had to change it to the previously used SSID and pass.
SaHaRzZz reacted to W-L in Fitting Push/Pull fans on NZXT H400
Having push pull on the rad will help somewhat, if you need to add a fan on the outside you can use some washers to have the fan spaced off of the raised honeycomb of the case and use some longer screws. Just note the length and make sure they are not too long to the point where they will fit the rad itself.
SaHaRzZz got a reaction from Stormseeker9 in How can I properly install a thermal sensor?
As of right now, my idle temps are at 33c, browsing and youtube temps are at 37c, and max stress test 65c at max.
before that it was sitting at 55c idle and 78 stress test while being noise af.
So yeah I'm happy about it, and of course I installed aftermarket heatsinks on every VRAM and VRM module on the card,
it's pretty good id say