Jump to content
Search In
  • More options...
Find results that contain...
Find results in...

derr12

Member
  • Content Count

    272
  • Joined

  • Last visited

Reputation Activity

  1. Informative
    derr12 got a reaction from thechinchinsong in Any server nerds in the house? Dell Canada publish specs on 3 upcoming 7nm Epyc Milan CPUs confirming rumours   
    Been running first gen epyc for over 2 years.  vsphere.  Its rock stable on the supermicro platform.
  2. Informative
    derr12 got a reaction from StDragon in Any server nerds in the house? Dell Canada publish specs on 3 upcoming 7nm Epyc Milan CPUs confirming rumours   
    Been running first gen epyc for over 2 years.  vsphere.  Its rock stable on the supermicro platform.
  3. Funny
    derr12 got a reaction from Asez23 in RX 6000 and RTX 3000 Series Shortages Partly Caused by GDDR6 Shortage, Supply Unlikely to Return to Normal Until Feb.   
    just make sure to use a GPU with a back plate. the old school nakid PCB video cards will tear you several new ones... or at least go fan side up. 
  4. Funny
    derr12 got a reaction from HelpfulTechWizard in RX 6000 and RTX 3000 Series Shortages Partly Caused by GDDR6 Shortage, Supply Unlikely to Return to Normal Until Feb.   
    just make sure to use a GPU with a back plate. the old school nakid PCB video cards will tear you several new ones... or at least go fan side up. 
  5. Funny
    derr12 got a reaction from CarlBar in RX 6000 and RTX 3000 Series Shortages Partly Caused by GDDR6 Shortage, Supply Unlikely to Return to Normal Until Feb.   
    just make sure to use a GPU with a back plate. the old school nakid PCB video cards will tear you several new ones... or at least go fan side up. 
  6. Like
    derr12 got a reaction from Heiks in Gpu block flow direction   
    ive got my block for my 5700xt running in reverse flow.  works fine.
  7. Funny
    derr12 got a reaction from Warin in Where Gaming Begins - AMD RX6000 series Live Event   
    a virtual machine that simulates the old rage128 cards.  time to bust out your descent and descent2 floppies folks!
  8. Informative
    derr12 got a reaction from Mark Kaine in Where Gaming Begins - AMD RX6000 series Live Event   
    a virtual machine that simulates the old rage128 cards.  time to bust out your descent and descent2 floppies folks!
  9. Funny
    derr12 got a reaction from Tan3l6 in Where Gaming Begins - AMD RX6000 series Live Event   
    a virtual machine that simulates the old rage128 cards.  time to bust out your descent and descent2 floppies folks!
  10. Funny
    derr12 reacted to minibois in Nagao shows off GPU Mirror so you can admire the beauty of your GPU fans   
    I should start a petition to call this a Fanity Mirror.
  11. Like
    derr12 got a reaction from BiG StroOnZ in Desk PC v2 *complete for now*   
    I’ve got trim pieces to sort out, but it runs. And the required cinnibench run.



  12. Like
    derr12 got a reaction from Radioactive Snowman in Here’s why Apples $700 Wheels are NOT Crazy   
    I gotta say, that is turning into a pretty stylish beard.  
  13. Like
    derr12 got a reaction from Ben17 in Operation "E.T. go home" Alienware Aurora restoration   
    iffy memory controller, correct me if im wrong but this gen still had memory controller on mobo right?
  14. Informative
    derr12 got a reaction from Bombastinator in Computer turns off for one or two seconds before turning on   
    sounds like the memory training behavior i saw on my first-gen ryzen/x370 board. 
  15. Like
    derr12 got a reaction from NotABigGamer in Desk PC v2 *complete for now*   
    I’ve got trim pieces to sort out, but it runs. And the required cinnibench run.



  16. Like
    derr12 got a reaction from oscar7601 in Copper monobloc starts corroding after fluid swap   
    you can clean the nasty areas with viniger.  wont hurt copper.
  17. Like
    derr12 got a reaction from NotABigGamer in Desk PC v2 *complete for now*   
    And the side grille. 

  18. Like
    derr12 got a reaction from BiG StroOnZ in Desk PC v2 *complete for now*   
    Hard tubes fit.  Next up is getting the replacement motherboard with a clean block installed. Then filling and leak testing. Also some cable management.

  19. Like
    derr12 got a reaction from Orangeator in Desk PC v2 *complete for now*   
    Hard tubes fit.  Next up is getting the replacement motherboard with a clean block installed. Then filling and leak testing. Also some cable management.

  20. Like
    derr12 got a reaction from NotABigGamer in Desk PC v2 *complete for now*   
    Hard tubes fit.  Next up is getting the replacement motherboard with a clean block installed. Then filling and leak testing. Also some cable management.

  21. Like
    derr12 got a reaction from NotABigGamer in Desk PC v2 *complete for now*   
    Using fan splitters to get all 8 fans turning now. Decided to wash my rad out and pump. And now I’ve got the bottom part of the case all tubed up. 



  22. Funny
    derr12 got a reaction from Orangeator in Desk PC v2 *complete for now*   
    yep. mosfet controlling 2 fan ports was dead.  slipped right off its mounting. soldered it back on, but not getting enough juice to turn a fan.  oh well, ordered another one and will use fan splitters to get all 8 spinning for now. I probably killed it.  turns out one of my fans was shorting out thru the heatshrink.  must have left a jaggy.
  23. Like
    derr12 got a reaction from NotABigGamer in Desk PC v2 *complete for now*   
    Rgbw test semi-successful. A couple colours missing on a couple strands. These build your own kits have really really finicky connectors. Went thru the whole damn roll to get this good. Cheap no-name controller. 


  24. Like
    derr12 got a reaction from Orangeator in Desk PC v2 *complete for now*   
    Rgbw test semi-successful. A couple colours missing on a couple strands. These build your own kits have really really finicky connectors. Went thru the whole damn roll to get this good. Cheap no-name controller. 


  25. Like
    derr12 got a reaction from BiG StroOnZ in Desk PC v2 *complete for now*   
    We are getting close. Another coat inside the cabinet and another couple on the trim bits here and there. I may be able to start mounting hardware by tomorrow night.
     
     

×