Jump to content
Search In
  • More options...
Find results that contain...
Find results in...
Ts2001

Cpu Temp High on Customloop

Recommended Posts

Posted · Original PosterOP

Hi,

 

A week ago i finally got a customloop. (240+360 rads)

And my gpu temp seemed fine. (Around 40c on load)

But my cpu is reaching 80c. 

I tried reseating the cpu waterblock, made sure the nuts are as tight as they can go and reapplyed the thermal compound but no improvement.

Specs:

i7 4770k 1.225V 4.2 Ghz

Link to post
Share on other sites

CPU loop pump dead / fans not spinning / somewhere leaking coolant?


Studying abroad, ditched the crappy laptop for a mobile workstation/gaming laptop double WITH CRAPPY THERMAL PASTE THAT 1/2 THE CINEBENCH SCORE

Model: HP Omen 17 17-an110ca CPU: i7-8750H (0.125V undervolt) GPU: GTX 1060 6GB Mobile (1700MHz 0.812V) RAM: 12GB DDR4-2666 CL19 (timings are so loose, might as well have lower frequency). Storage: 128GB Toshiba NVMe SSD (KBG30ZMV128G) + 1TB Seagate 7200RPM 2.5" HDD (ST1000LM049-2GH172) Monitor: 1080p 120Hz IPS G-sync

 

The best thing to do is reading the clock speed that doesnt end in a pair of zeros. Software voltage readings are wrong if your motherboard's not a high end model

CPU: i7-2600K 4493MHz (multiplier: 43x) 1.35V (software) --> 1.4V at the back of the socket Motherboard: Asrock Z77 Extreme4 (BCLK: 104.5MHz) CPU Cooler: Noctua NH-D15 RAM: Adata XPG 2x8GB DDR3 (XMP: 10-11-11-30 2T 2133MHz, custom: 10-11-10-30 1T 2229MHz) GPU: Asus GTX 1070 Dual SSD: Samsung 840 Pro 256GB (main boot drive), Transcend SSD370 128GB PSU: Seasonic X-660 80+ Gold Case: Antec P110 Silent, 5 intakes 2 exhausts Monitor: AOC G2460PF 1080p 144Hz (OC'd 150Hz) TN Keyboard: Logitech G610 Orion (Cherry MX Blue) with SteelSeries Apex M260 keycaps Mouse: BenQ Zowie FK1

 

Results: Cinebench R15 Single thread:159 Multi-thread: 770 (thx Meltdown Spectre patch) Super Pi (v1.5 from Techpowerup, PI value output) 16K: 0.11s 1M: 8.4s 32M: 7m 45.9s

Link to post
Share on other sites
1 minute ago, Jurrunio said:

CPU loop pump dead / fans not spinning / somewhere leaking coolant?

Air pocket could also be the cause.


CPU:Intel i7 3930k w/OC & EK Supremacy EVO Block | Motherboard: Asus P9x79 Pro  | RAM: G.Skill 4x4 1866 CL9 | GPU: EVGA GTX 780 Classified w/OC & EK Water Block | SoundCard: Asus Xonar D2X - FiiO X3K DAP/DAC for Headphones | Storage: Samsung 850 Pro 1TB SSD + Samsung 850 Evo 256GB SSD | Cooling: XSPC D5 Photon 270 Res & Pump | 2x XSPC AX240 White Rads (Push) + NexXxos Monsta 80x240 Rad (Push/Pull) | PSU: Seasonic Platinum 1000w | Case: Modded CM Storm Stryker

Link to post
Share on other sites
3 minutes ago, SolarNova said:

Air pocket could also be the cause.

less likely. Air pocket in the coolant can cause bouncy temps, but not consistently high temps. In the thermal paste... then that's a really bad application.


Studying abroad, ditched the crappy laptop for a mobile workstation/gaming laptop double WITH CRAPPY THERMAL PASTE THAT 1/2 THE CINEBENCH SCORE

Model: HP Omen 17 17-an110ca CPU: i7-8750H (0.125V undervolt) GPU: GTX 1060 6GB Mobile (1700MHz 0.812V) RAM: 12GB DDR4-2666 CL19 (timings are so loose, might as well have lower frequency). Storage: 128GB Toshiba NVMe SSD (KBG30ZMV128G) + 1TB Seagate 7200RPM 2.5" HDD (ST1000LM049-2GH172) Monitor: 1080p 120Hz IPS G-sync

 

The best thing to do is reading the clock speed that doesnt end in a pair of zeros. Software voltage readings are wrong if your motherboard's not a high end model

CPU: i7-2600K 4493MHz (multiplier: 43x) 1.35V (software) --> 1.4V at the back of the socket Motherboard: Asrock Z77 Extreme4 (BCLK: 104.5MHz) CPU Cooler: Noctua NH-D15 RAM: Adata XPG 2x8GB DDR3 (XMP: 10-11-11-30 2T 2133MHz, custom: 10-11-10-30 1T 2229MHz) GPU: Asus GTX 1070 Dual SSD: Samsung 840 Pro 256GB (main boot drive), Transcend SSD370 128GB PSU: Seasonic X-660 80+ Gold Case: Antec P110 Silent, 5 intakes 2 exhausts Monitor: AOC G2460PF 1080p 144Hz (OC'd 150Hz) TN Keyboard: Logitech G610 Orion (Cherry MX Blue) with SteelSeries Apex M260 keycaps Mouse: BenQ Zowie FK1

 

Results: Cinebench R15 Single thread:159 Multi-thread: 770 (thx Meltdown Spectre patch) Super Pi (v1.5 from Techpowerup, PI value output) 16K: 0.11s 1M: 8.4s 32M: 7m 45.9s

Link to post
Share on other sites
Posted · Original PosterOP
8 minutes ago, Jurrunio said:

CPU loop pump dead / fans not spinning / somewhere leaking coolant?

its all 1 loop, the fans are spinning and no leakage visible.

 

Link to post
Share on other sites
Posted · Original PosterOP
4 minutes ago, Jurrunio said:

less likely. Air pocket in the coolant can cause bouncy temps, but not consistently high temps. In the thermal paste... then that's a really bad application.

Made sure that there was enough thermal compound

Link to post
Share on other sites

Since your GPU temps are good, your loop itself is working fine. So the problem must be the heat transfer from the CPU to the water.

Which block are you using? Have the temperatures been better before? Is the CPU delidded? Are you using the correct I/O on the block?

Link to post
Share on other sites
Posted · Original PosterOP
Just now, Dschijn said:

Since your GPU temps are good, your loop itself is working fine. So the problem must be the heat transfer from the CPU to the water.

Which block are you using? Have the temperatures been better before? Is the CPU delidded? Are you using the correct I/O on the block?

Its a Supremacy evo, i used to be able to get better temps on my NH D14, the cpu is not delidded and im using the correct I/O ports on the block.

Link to post
Share on other sites
Posted · Original PosterOP
10 minutes ago, Jurrunio said:

less likely. Air pocket in the coolant can cause bouncy temps, but not consistently high temps. In the thermal paste... then that's a really bad application.

 

14 minutes ago, SolarNova said:

Air pocket could also be the cause.

 

3 minutes ago, Dschijn said:

Since your GPU temps are good, your loop itself is working fine. So the problem must be the heat transfer from the CPU to the water.

Which block are you using? Have the temperatures been better before? Is the CPU delidded? Are you using the correct I/O on the block?

So i did a quick 5 min stres stest in aida.

20180613_154303.jpg

Link to post
Share on other sites

Is it a Evo block for this socket?

I would also check the already named things:

- air pockets

- wrong screws/springs

- wrong mounting

- bad thermal paste

 

In the end the Evo is not the best block, but you should easily outperform an aircooler.

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


×