Jump to content
Search In
  • More options...
Find results that contain...
Find results in...

johnnyleano69

Member
  • Content Count

    28
  • Joined

  • Last visited

Awards


This user doesn't have any awards

About johnnyleano69

  • Title
    Member

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. i will do that right now
  2. Well i think the ISP router already is configured to DHCP and yes i would like to find out more and what do i need to do to give u more information
  3. Well i think the ISP router already is configured to DHCP and yes i would like to find out more and what do i need to do to give u more information
  4. This is what the set up basically looks like except i was running the ethernet from the back of the modem directly to the cisco router
  5. Router(config)#Success rate is 0 percent (0/5) ^ % Invalid input detected at '^' marker. Router(config)#Router(config)# ^ % Invalid input detected at '^' marker. Router(config)# *Jul 17 07:18:00.187: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down *Jul 17 07:18:01.187: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down Router(config)# Router(config)# Router(config)# Router(config)#exit Router# *Jul 17 07:30:15.983: %SYS-5-CONFIG_I: Configured from console by console Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int g0/0 Router(config-if)#no shutdown Router(config-if)#ip address dhcp Router(config-if)#exit Router(config)#exit Router# *Jul 17 07:31:16.251: %SYS-5-CONFIG_I: Configured from console by console Router#do ping 8.8.8.8 ^ % Invalid input detected at '^' marker. Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#do ping 8.8.8.8 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) Router(config)# *Jul 17 07:32:07.187: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up *Jul 17 07:32:08.187: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up Router(config)#do *Jul 17 07:32:18.251: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0/0 assigned DHCP address 192.168 .1.116, mask 255.255.255.0, hostname do ping 8.8.8.8 ^ % Invalid input detected at '^' marker. Router(config)#do ping 8.8.8.8 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 12/12/16 ms Router(config)# So i decided to check if connecting the router directly to my isp router would work and see what would happen so it goes ISP Modem > ISP Router > Cisco 2921 Router > ( Then planning to set up a Cisco 2950 Switch with it as well ) I was wondering why this work instead of the original configuration i had which was ISP Modem > Cisco 2921 Router > (2950 Switch ) i feel like i cheated i process though. It is for labs but maybe i was doing it wrong ?
  6. Router>enable Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int g0/0 Router(config-if)#no shutdown Router(config-if)#i *Jul 17 07:13:04.603: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to dow Router(config-if)# *Jul 17 07:13:09.187: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up *Jul 17 07:13:10.187: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up Router(config-if)#ip address 192.168.2.1 255.255.255.0 Router(config-if)#exit Router(config)#do ping 8.8.8.8 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) Router(config)#do ping 8.8.8.8 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) Router(config)# This is where i am at now
  7. geez i think i am two steps back now. So i started it up and then i realized that it didn't save. So i reconfiged the g0/0 interface so i did router> enable Router#config t Router(config)#int g0/0 Router(config-if)#no shutdown Router(config-if)#ip address dhcp Router(config-if)#do ping 8.8.8.8 % Unrecognized host or address, or protocol not running. Router(config-if)#exit Router(config)#do ping 8.8.8.8 % Unrecognized host or address, or protocol not running. router
  8. im gonna keep worklng at it since i just woke up
  9. So after a few more tries i finally got back around to the do ping .8.8.8.8 and it was successful with the connection but i reached another impass once i was trying to configure dhcp These screen shots were also taken with the ISP connection running through it because i needed to hop back on my computer to find more help
  10. thank u i will do that now
  11. i will get a screenshot to better show my issues
  12. Well let me be honest i am kind of new to the whole cisco world. So i cleared the cleared the configurations that were on it I think connected the ethernet cable from my modem to Interface g0/0 I then did router> enable entered my password router# config t router#(config) int g0/0 router#(config if)no shutdown router#(config if)ip address dhcp router#(config if) exit router#(config ) do ping 8.8.8.8 thats when i got the error message
  13. Hi, I'm trying to set up some labs on my router and switch. I have been watching several videos on how to configure the ports on the router. I get to setting up DHCP and then when i do a "do ping 8.8.8.8" i get 0/5 succession rate. I ran debug mode but i also see that it says un-route able so i must be missing something. Please help
  14. Oh okay i was a bit worried i was going to have to buy the server board. Anyways, you think you could me set them up? or give me some insight i can't seem to get past the 3 GPU
  15. Sorry I'm a fairly new to all this. So how many does it actually have. I just went to my local tech store and look at the inside of the board and thought to my self " oh yeah i can stick 6 riser boards to this" i'm just trying to better understand my mistake
×