maharshi1234

Can't afford. Its ok. I accepted. But this ded only in 3 years. Those are some trip photos of me and my brother. Remaining data are games.

Tried clearing CMOS. Didnt work. Its not bootmenu sorry. In BIOS mode, we can see list of connected SATA devices. It shows empty for HDD port. How do i recover data?

Will try after clearing CMOS. Also forgot to mention. In Boot menu, in SATA tab, it doesn't show this HDD. It only shows SSD there.

I have my childhood photos in it. I didn't have a backup. I tried to reinitialize it using AOMEI. It gives Error I/O error.

It shows like this

I changed my SSD and HDD sata wires. I only have 2. But not solved

I have been using this HDD from 3 years. Suddenly it is not showing in Documents. In Disk management, it shows Unknown. Not initialised. I tried all the tutorials. Tried to rebuild MBR. Tried to clear data from diskpart. It says failed due to I/O error. Also tried changing the SATA cables. Did my HDD die?

I have moved intake fan a little bit upwards so CPU will take that air. And added exhaust on top. Also i added another intake on PSU shroud. But there is a little gap between PSU and Fan. But i have openings on back of my case. Will that fan work fine? If that doesn't work, what can be the next possible position other than front and side panel? Back view:

Thank you. Yes i got inspired from Lian o-11 case. I will add two more fans. Also can i put one intake fan on shroud and make some holes at the bottom of case? And i will add 1 more exhaust at top. Also i only have Stock AMD cooler. I will make few changes and add 2 fans and will post picture in an hour.

Can i reduct temps if i add two more fans? One more exhaust at top and one more intake above the present intake fan. What is the difference between DIY case and prebuilt one?

Thank you. First time building case. Hope it goes well.

Ok i will check

Yes. I will make circle hole inside that can fit fan. In back of case, i will make larger rectangular hole and put mesh there.

Oh thanks

Case will have dimenstions 510mm x 470mm x 240mm. Is this good?

My first PC i am building DIY case. I can only buy two 120mm fans now. I will keep one exhaust and 1 intake. In the following picture, i put intake fan at right side. Is this good airflow? Will i have any bad airflow? I am thinking that air will touch the side panel and reflect back and limit airflow. I know if i put that fan in front side, then i think there will be good airflow. But i want to make 3 sides(top, front,left) acrylic panel without any holes. Is this fans position good or bad idea?

Sorry for late reply. I have bunch of Arduino Jumper wires. They are just wires that can be connected easily to motherboard pins. So can i use 1st and 2nd pin of motherboard to run 2 fans? If i have 1 PWM fan and 1 Voltage control fan. Can i use Voltage control for both of them. If yes, then only 1st and 2nd pin are enough? 1st pin of motherboard will go to 1st pin of both fans pins parallel. 2nd pin as same. The place i am living doesn't have good fan splitters so i am just using jumper wires. Are these how splitters work? If this is not possible then i will take 12V supply of PSU molex and run additional fan at full speed.

Yes i understood. I want to connect 2nd fan with a jumper pin. So the PWM signal will send to both fans. Will that work?

So you saying that i can control 1st fan but 2nd fan will have full speed? I did not understand what will be the 1st and 2nd fan. They are parallel connection. So it will be random or what?

Yeah i checked. But in my region there are not 4pin ones available. But i have so many jumper wires. I can use them in parallel i think.

Ok. That 4th pin is for speed control right? If i connect more fans, All fans can be controlled at once? Will that work?

My motherboard Gigabyte A320M-s2h has only one 4-pin fan header. I want to add 2 or 3 fans in my cabinet. I have jumper wires. Can i connect 2 or more fans in parallel connection to that single pin? Will that work? Or will it damage anything?

This is new card. My cabinet is so small/ I doesnt have good airflow. May be that is causing issue. I am using with left panel open for now. It is getting me 75 to 78 degrees on 100% load. I will try increasing fan speed today.

Also i don't have any case fans. My money is all over buying components. i will buy new cabinet in August or september. until then i want to use this.

How to change fan speeds?