Jump to content
Search In
  • More options...
Find results that contain...
Find results in...

TheBeast108

Member
  • Content Count

    40
  • Joined

  • Last visited

Everything posted by TheBeast108

  1. On your “more specifically this one” do I have to download them both? If so, how? I’d assume download them on another pc and plug in a flash drive with the drivers on it into the pc, but then how do I like extract them and actually install them?
  2. Hi all, as title mentions I cannot connect to the internet at all using the wireless adapter. I have a ASUS ROG Strix B550-E gaming with Intel WiFi 6 AX200, with an antenna. I can’t access the internet and when I click on the no internet icon on the bottom it says “Network & Internet settings” then under that says “Change settings, such as making s connection metered” It shows no available connections at all and I’m at a loss. Been trying to figure it out for an hour now and can’t find anything.
  3. I’m taking that as I click ‘ok’ for it to change the fan from auto to dc?
  4. But then that’s where the initial question I had was, do I click ok on this or how do I change it to pwm, but I’m pretty sure it’s already in pwm mode
  5. How do I do that in here? https://imgur.com/a/W3hxRDA
  6. Oh yes, here you go https://imgur.com/a/XJcdlQ6
  7. Never went into bios before, I’m using all LL120 fans from Corsair, I was about to install windows but then when I went to exit and save this popped up and I don’t know if I should click yes or change something.
  8. It wasn’t the motherboard, ended up being the GPU came DOA, I’m using a GT740 as a temp GPU and it booted up into bios fine today
  9. Oh yes sorry, forgot to post specs; ASUS ROG Strix B550-E gaming motherboard G.skill trident z 16gb 3200Mhz Ryzen 7 3700X ASUS ROG Strix RTX 2070 super advanced 8gb Samsung 970 evo 1TB Corsair HX850 platinum power supply Everything is spinning and on, including the white LEDs where the PCIe cables plug into the graphics card, the graphics card LEDs are ok and the fans are spinning. I haven’t tried running a single stick of memory yet. I’ll try that now. The HDMI cable works fine as it was working perfectly with my laptop yesterday, and it is plugged in firmly to the gpu and it a tad bit loose on the monitor end, but nothing seriously loose.
  10. I called ASUS support and went through a few troubleshooting steps with them and nothing worked and they said my motherboard was defective. I sent it back to amazon for a replacement and have built my pc again, only this time to have nothing changed. Screen turns on to ‘HDMI NO SIGNAL’ then goes to sleep. No QLED LEDs show after a minute of starting the system. The only one to last longer than the others is the BOOT QLED but then it turns off. I have the Qcode AA, which from what I’ve read means that it transitioned into ACPI mode, which means that it was handed over to the operating system. I don’t know what I can try at this point.
  11. Called asus support, did CMOS, didn’t work, they confirmed it’s defective and now it’ll take 2 weeks for me to send it back, have them repair it, and send it back. They said 7-10 business days.
  12. Okay. So just to be clear on steps, I remove the battery, (after unplugging everything) hold down the case powerbutton for 30 seconds, the put the battery back in and turn on the pc?
  13. A friend sent me a video from asus. It’s not the cpu, gpu, or ram. I’m pretty sure it’s my ssd. When the pc turns on it checks itself. My gpu, cpu, and ram pass but the ssd isn’t. (I only have my SSD plugged in as I have no room for my harddrive.) so that would be the only thing it could boot from. I’ll still reset the CMOS, but I think if I could get a signal to my monitor and if I could get into bios, I think I could fix the boot issue also, shouldn’t I leave the CMOS battery out for 5 minutes? And after I take it out, hold down the power button for 30 seconds like you said, but still wait that other 4 minutes and 30 seconds before putting the gpu back in?
  14. I tried only one ram stick in slot B2 as said for single stick in the manual, then it started lashing the red led, white led, then went to the boot led. I guess cmos is my only option now. Is it fine to leave the graphics card out when I do that? And do I leave it out for a minimum of 5 minutes?
  15. Should I take out the battery to clear CMOS or should I jump the connection on the two pins with a metal screw driver or something?
  16. https://imgur.com/gallery/EvkAkD9 Specs are; ASUS ROG Strix RTX 2070 super advanced 8gb Ryzen 7 3700X Asus rog Strix B550-E Gaming motherboard 5 Corsair LL120 fans Corsair lighting node core Corsair HX850 watt platinum rated PSU G.Skill trident Z 16gb 3200Mhz Corsair H100i platinum SE Corsair 465x case Windows 10 home (not installed yet) Ive reseated both sticks of ram, but I can also try just one. The boot led came on AFTER I reseated the GPU. Yesterday/last night, it was a VGA error LED
  17. Directly into the graphics card. The cable I know is fine as yesterday before I tried to POST I had it plugged into my laptop and it was working fine
  18. Been having issues trying to get it to POST, it is giving me a yellow green LED now and it wasn’t yesterday. But I was wondering if these white LEDs are supposed to be on. https://imgur.com/gallery/fDKZUOm Specs: ASUS ROG Strix RTX 2070 super advanced 8gb ASUS ROG Strix B550-E Gaming mobo Ryzen 7 3700X 16gb ram PC has the A9 code still, which means it’s start of setup but I don’t know how long it’s supposed to stay like that.
  19. I reseated the graphics card, it’s not stuck on AA, it’s on A9, is that normal, if so, how long does it take to do the start of setup which A9 means? still have no signal either
  20. Basically, first time pc builder, and the white VGA error led showed and someone suggested I shut down the pc, wait 30 seconds, and start it up again, that worked and got rid of the white led, but I still have no signal on my monitor, I know the cable is good because it worked just fine with my laptop earlier today. It’s also giving me the AA code also. Specs: ASUS ROG Strix RTX 2070 super 8GB advanced edition Asus rog Strix B550-E Gaming mobo 16gb ram Ryzen 7 3700X
  21. Basically, first time pc builder, and the white VGA error led showed and someone suggested I shut down the pc, wait 30 seconds, and start it up again, that worked and got rid of the white led, but I still have no signal on my monitor, I know the cable is good because it worked just fine with my laptop earlier today. It’s also giving me the AA code also. Specs: ASUS ROG Strix RTX 2070 super 8GB advanced edition Asus rog Strix B550-E Gaming mobo 16gb ram Ryzen 7 3700X
×