JESUS IS LORD

RIG : 
MOBO : Msi Carbon Pro Gaming 
CPU : Ryzen 7 1700 @ 3.9ghz
Ram : Currently 16gb of Geil Super Luce @ 3000mhz R.....G.......B ... had to RMA 16gb .. will have 32gb
GPU : Gtx 1070 Founders Edition's Plural in SLI @ +220 on the Core and +520 on the memory on both cards
NVME SSD : 2TB Saberenth Rocket, 250 gb Muchkin Drive ... NO HDD ALL NVME STORAGE!!! 
Rad : Dual 360 Rads 
Case : Lianli PC-011 Dynamic  
Distro Plate : Barrow for the Lianli PC-011 Dynamic  
 
RES AND PUMP are behind the mobo 
No Cable Management Required 
Put rgb strips behind 2 of the tubes, will buy more and do them all .. used superglue to attach ... they are 50/50 so the have a rubber outer coating!
dont put super glue on RGB strips directly they will short and cause a fire! 
 

yes, that is not when i have issue, but regardless when there is no overclocking at all it was only showing 7.6gb out of 16gb.. the RAM is rated for 3000Mhz.. I was running it at 3000Mhz... pretty straight forward ... The Voltages were set properly... 

RIG : 
MOBO : Msi Carbon Pro Gaming 
CPU : Ryzen 7 1700 @ 3.9ghz
Ram : Currently 16gb of Geil Super Luce @ 3000mhz R.....G.......B ... had to RMA 16gb .. will have 32gb
GPU : Gtx 1070 Founders Edition's Plural in SLI @ +220 on the Core and +520 on the memory on both cards
NVME SSD : 2TB Saberenth Rocket, 250 gb Muchkin Drive ... NO HDD ALL NVME STORAGE!!! 
Rad : Dual 360 Rads 
Case : Lianli PC-011 Dynamic  
Distro Plate : Barrow for the Lianli PC-011 Dynamic  
 
RES AND PUMP are behind the mobo 
No Cable Management Required 
Put rgb strips behind 2 of the tubes, will buy more and do them all .. used superglue to attach ... they are 50/50 so the have a rubber outer coating!
dont put super glue on RGB strips directly they will short and cause a fire! 
 

bad power plug ... plugged it in a different outlet and it was good to go .... had some tubes that did not want to stay in but i used a little super glue and then put it and now it is solid .. its not coming back out, but i do not think i will have need of taking it out

i use 3 .. Cinebench is a good quick indicator if your checking overclocking stability ... if you can run 3 back to back runs its probably good enough ... then i will run Aida 64 for 30 min or so once Cinebench has passed ... and then for GPU 3d Mark is where its at !!! Using Msi Afterburner to dial in your overclock

well it was doing something funky .... i set it 1.400v posted fine and then when i check my voltages they are like at spiking to 1.50v in cpuid ? its overriding my voltages?  i lowered my cpu to 3.98ghz .. 1 teir lower than 4.0 ghz and lowered my voltages and it goes about two or three minutes before crashing on fpu in aida 64 , 4.0 ghz is instant crash on Fpu, but Cpu all other test run fine? Also I am able to 3 back to back cinebenches, which is a very good indicator of stability ...  

yes, well ryzen 7 1700 max ive seen is 4.1"Ghz" which i would like try if i can stabilize 4.0mhz ... i remember that overvolting was causing stability issues in the past