GMW
-
Posts
17 -
Joined
-
Last visited
Content Type
Forums
Status Updates
Blogs
Events
Gallery
Downloads
Store Home
Everything posted by GMW
-
So funny story. The cables I am using to connect my gaming rig to the switch are only rated for 100mb/s but they are cat6. Switched cables and am getting 1000mb/s total now. Is there a way to get 1000mb/s for each port?
-
Each port has it's own ip address on the lan. And it does use all 4 at the same time when transfering files from my server. But they are stuck at 100mb/s each when the card is designed for 1gb/s each. And the intel pro software wont let me configure it. Like the drivers are not installed even though they are.
-
So I have a home server with a quad gigabit network card. And it is hooked to a gigabit switch. I've tested it from a rig with a gigabit port and got 1gb/s copy speeds. Today I installed another quad gigabit card into my gaming rig hoping to get 4gb/s copy speeds. But I'm only getting 400mb/s. I've checked drivers, I've checked anything in bios. Nothing is adding up to why I'm not getting 4gb/s. And the switch I have lights up green for 1000mb/s and yellow for 100mb/s. So it isnt getting a gigabit connection. Please help. Card is: Intel Gigabit ET Quad Port server adapter. I have same card in my server running windows 10. And no issues. Only different is my server is a amd threadripper and this is an intel.
-
Well looked closer to how I had it configured, due to how my water lines run I have a hard to getting to my RAM slots. I'm ashamed to admit they were in wrong slots. Moved over and works perfect. Thanks everyone for the ideas. I would never of looked at slot had someone not suggested.
-
Yeah they are in right slots. And yeah tried running higher the 3200mhz. No boot no matter what. Tried volt changes from early post. No change
-
Took block off and I must have a newer one. Thos stand offs aren't even there.
-
Doesn't seem to wanna boot with those setting applied. Should I of left the DOCP setting enabled?
-
alright yeah if you get into BFV and don't see anything odd its probably not that. I just don't think its windows if it happens in bios and before windows boots. my opinion.
-
Can you get into a game at all? I had same problem with one of the early 2080ti cards that had bad memory chips. and did that but in windows was fine but in games i got serious artifacting. This might not be the same issue but the only time i've seen that is with the bad 2080ti. just an idea, it might not help.
-
That to me looks like a GPU issue.Just an idea where to look.
-
i'm away from it atm. I will try when i get a chance pretty sure i tried that already though or something similar. but ill sanity check when I can.
-
Specs: Asus ROG Crosshair VII Hero (x470) Ryzen 9 3900x G.SKILL Trident Z Neo (For AMD Ryzen) 32GB 3600mhz https://www.newegg.com/g-skill-32gb-288-pin-ddr4-sdram/p/N82E16820232861?Description=gskill neo&cm_re=gskill_neo-_-20-232-861-_-Product I can apply the the DOCP and get the timings right but anything over 3200mhz i cant post. I've made sure I have latest BIOS installed. My RAM kit is on the 3000 series compatibility chart. I've tried to adjust voltages and timing manually and just can't seem to get it to boot at 3600mhz. My theory is that because it is an x470 chipset that im just waiting for the right BIOS update. Any ideas?
-
Thanks. That would make sense. I'll try it when I get a chance!
- 8 replies
-
- 1
-
-
- graphics cards
- 2080ti
- (and 4 more)
-
But if thermals go down in temp, shouldn't the auto overclock boost higher?
-
Auto oc, any overclock I apply crashes when I load into a game. Even small overclocks.
-
Yep, power and thermal limits are maxed.
-
I have a 2080 ti strix card on water. Started out haveing a small thermal issue were it was sitting in low 80 degrees and would only hit about 1935 mhz, and would not take any overclock at all. I've since fixed the thermal issue and it sitting in the mid 50 degrees now and it actually performs worse around 1905 mhz and still no overclock will work. I am using MSI afterburner and have power and thermal limits set to max. The block is installed correctly as far as I know. Any Ideas?
