JustSum

I don't have any experience with those, but seems like it should be fine.

If you can these are Samsung bdie chip that can do 3600 at c16 well the one i have can and i can do 3800 at c16 and 17
Easy 3200 at c14 since all you go todo is turn on xmp.
I sometimes see the 
T team force on sale for around 110.
https://www.newegg.com/g-skill-16gb-288-pin-ddr4-sdram/p/N82E16820232530?Item=N82E16820232530&nm_mc=AFC-RAN-COM&cm_mmc=AFC-RAN-COM&utm_medium=affiliates&utm_source=afc-PCPartPicker&AFFID=2558510&AFFNAME=PCPartPicker&ACRID=1&ASID=https%3a%2f%2fpcpartpicker.com%2fproduct%2fwX7CmG%2fgskill-flare-x-series-16gb-2-x-8gb-ddr4-3200-memory-f4-3200c14d-16gfx&ranMID=44583&ranEAID=2558510&ranSiteID=8BacdVP0GFs-wbBHOoda71P7FrWR7zZNcA
 
https://www.google.com/amp/s/www.newegg.com/amp/team-16gb-288-pin-ddr4-sdram/p/N82E16820313712
 
https://benzhaomin.github.io/bdiefinder/
 

The highest frequency setting that does not need 2:1 ratio and mismatched FCLK

everytime i try to enjoy facts like this i've encountered in my life i think about all the warehouse employees peeing in bottles and it ruins it

You lucky bastard

Just wanted to make sure yep i can keep it.lol

@JustSum
 
i think the temps/voltage readouts are there, they just hide on the side.
 
i looked at my BIOS and you can click the expand bar to see them again. Arrow on the right for expand/collapse.

Yeah but come on it doesnt have reset cmos that I noticed no ,only 1 hdmi my other board ias hdmi and hdmi and display port. Yes im just 
nitpicking. Thnx for all the help.
Ps. Yes ik no one buys this kinda board to use the integrated gpu, but i do use. Time to emty my sistem.

I'll bet 5 chocobo feathers that it works.

It was like new from amazon still has all the plastic . I'll just return it no point. I'm sure i can just bend it back but why risk it.

-Links Removed-
Just to abide the community standards

Hey everyone, I do a lot of reading but don't post much on this forum.  I figured I would share my experience with installing an Arctic Accelero III (or IV) on an RX 5700/5700XT.  Let me start by saying I purchased a Sapphire branded 5700XT along with an R5 3600 on launch day.  I was disappointed to find my card was unstable and would heavily throttle even on stock settings.  It was doing this because the junction temperature would quickly reach 110 degrees +.  I did try Gamer's Nexus' thermal paste and washer trick but that did not help even with a very aggressive fan curve.  I figured I was unlucky and received a card that had a slight manufacturing defect in the stock cooler or possibly a bad component running hot.  Since I planned to eventually use an aftermarket cooling solution anyways I decided to give it a go.  I went with the Accelero III as the IV's backplate would not fit in my application.  Below are pictures accompanied by tips of each step.
 

This was my solution for heat sink placement.  Due to the large mounting bracket you need to get creative on where you mount the VRAM heatsinks.  Use the 4 "skinny" heatsinks mounted almost to the far edge from the GPU for the chips along the side.  You can use 2 "square" heatsinks for the top chips but they need to be mounted almost halfway off of each chip to clear the heatsink.
 


I HIGHLY recommend using the factory back plate.  I originally mounted everything up without and the card just isn't sturdy enough on it's own.  Use the 6 factory backplate screws and size M2.5 nuts with plastic or fiber washers between the board and the nut.  I would recommend washers around 1mm or so thick.  If you go too large the factory screws aren't long enough.  Also, the rear mounting bracket won't quite clear the back plate.  Instead of using the 4 black spacers the Accelero instructions call for use the 4 white 4.5mm spacers included with the kit (they're the ones intended for the front mount on older GTX 4 and 5 series cards).
 

Everything mounted and ready for installation.
 

I am truly amazed at the difference.  I now have a quiet card that runs properly and has a good amount of overclocking headroom.  I was playing around with the soft power play table mod running at 1.25 volt on the core with a +50% power limit and I never went beyond a junction temp of 84 degrees and the GPU temp stays in the 60's.  For daily driving with a 1.2v core and +50% power limit I am 10-15 degrees less.  VERY HAPPY!
 

Maybe it's time to get in bed with team red.
 

I personally didn't have any issue using the included glue.  I had to remove and move heatsinks after I had glued them and let them cure overnight.  As long as you don't get crazy with the amount of glue you should be fine. 

Just like every other post ,1080 ti or wait for rtx 2080/ti benchmarks.