mikimarczyk

Whenever I boot my pc, my monitor is off for a while until windows loads, there isnt an asrock logo anymore or anything at all. I tried getting into the bios by spamming delete but all that happens is that my pc stays on but monitor isnt receiving anything. I also tried getting into the bios through windows by holding shift on the restart button and all that but i still had the same result. https://au.pcpartpicker.com/list/wtYvwV

For raid 0 you need two identical drives im pretty sure.

After resetting cmos twice more, it posted and now works. Im super sketched out about it though because i know it will happen again and i just want it to be perfect

Yeah, I found a pack of watch batteries of my battery draw at home and put it in and it's still not outputting anything. Thank you for the replies though

I mean I built the computer for christmas so I dont think it would run out that quicky

It's been going for a soild 30min now so I don't know. When this has previously happened it just works after a bit of turning off the system by holding power button and turning it back on but saying that know sounds really dodgy.

There is no display output at all so i cannot get into bios, but i have cleared cmos twice, once with jumper and once with leaving cmos battery out for 15min.

I only have one stick of ram in the system, and after clear cmos I think it would be running at 2133 not 2666 XMP. And the ram is in the correct slot for single channel on my board.

This issue has been affecting me for a while now (see last posts) and I cannot figure out the cause. My PC will work for days on end and then one day when I want to get on it wont post and appears to be going through some power cycle. Heres a video: If you look closes in the bottom right of the case (where the drive bay is) you can see the light of my case fans dim and brighten up. I have reset cmos with jumper, and a couple days ago I updated to latest bios (4.60). I have reseated ram and gpu, unplugged and replugged all psu cabled into mobo, hdd and gpu. I have tried to boot with only hdmi and psu plugged in, still nothing and even with no hdmi, the case fans ramps up and down and the lights also brighten and dim. Any help is greatly appreciated .

In the stock XMP profile it was 2666 with 1.25V and I didn't think thats enough (but it worked), I still changed it to 1.35V as every video I've seen says 1.35V is where you want to be. Thanks for the replies though

Im using a pretty standard psu, but its by a reputable brand (corsair), no cable extensions and I dont see how there could be a short anywhere as all the extra psu cables are tucked in the back nicely. My mobo QVL has my specific kit on it, I'll still change the ram back to 2133 but I dont see how this would cause my system not to output to display but still appear on (lights up and all that), then again this is my first build. Thank you for your reply

If it was a short wouldn't the whole system turn off and not just appear black for 1-5 seconds?

Ram is at its stock XMP setting and cpu is stable at 3.9ghz (overnight stress test) and also this has happened before I overclocked.

So this isn't the first time this is happened to my system (look at my previous post), I don't know what is causing this problem but I'm starting to think I'm going to need a new motherboard. I went to turn on my pc today (https://au.pcpartpicker.com/list/wtYvwV) and it went into a boot loop with no display output. Gpu lit up, cpu fan started spinning and my case fans started spinning. But my case fans LED's started to dim and get brighter, I think this happens with every attempt to boot as it happens every second or so (These fans are the stock ones with the case and are just normal 3pin fans). I immediately think it is either the psu or mobo giving uneven power or something but while sprinting to google and leaving my pc in the loop, the asrock logo flashes and then back to a black screen, next time the fans lights dim I get a post and I'm straight into windows. Additionally to this my gpu driver got absolutely destroyed today (before this) and I had to try many many many times to get into safe mode to ddu it. I don't know whats wrong with my system but i've reseated everything (apart from cpu) and problems like this still occur. Also, with everything plugged in properly, the smallest tap of my desk (which my pc is on) can make my screen go black instantly crashing any 3D application. (I have ensured the pcie slot is properly latched and that BOTH screws are in holding the gpu)

I reseated the gpu when i reset cmos because I couldnt fit my fingers in between it to get the jumper.