tronder

Hi All, Just wondering if anyone knew how to update the firmware for an APC smx1500rmi2u with an AP9631 NMC. It has old firmware from 2011 I think and I don't see how to update it through the interface.

Hi all! Looking to upgrade to the Oneplus 7 pro 12gb from my Iphone 7 however concerned with the current issues plaguing the device. In particular the phantom touch, battery heating and high pitch noises. Any ideas on if i should get this phone or just wait till they resolve it?

Is there an automatic switch you can recommended that i add? It just needs an on off then all fans spin, it's really weird. must be some noctua fan logic that just turns the fan off after a while of low power.

They are wired in parallel, as i said before, if i turn them off and on then they both spin at the same time but if i let sunrise then only one spins then the other spins.... I'm thinking it has something to do with one fan requires more Voltage or current to start hence path of least resistance is the smaller fan?

I currently have them wired in parallel, but the bigger fan doesn't start when i allow the sun to slowly run them

Hi All,Just needed some advice on wiring of fans to cool the new Eddi i installed a week or two back.Using a 4W, 12V solar Panel - jaycar.com.au/4-watt-12-volt-solar-panels-amorphous/p/ZM9026Noctua NF B9 REDUX 92mm - noctua.at/en/nf-b9-redux-1600-pwmNoctua NF R8 REDUX 80mm - noctua.at/en/nf-r8-redux-1800-pwmMy question is what is the best way to wire these fans to the solar panel?I currently have them both tapping into the solar panel at the same spot. If i power them on at the same time both fans spin. However if i let the sun slowly power them up e.g. from sunrise. Only the 80mm fan spins untill i cover the solar panel entirely, let the fans spin down and then power them up.Should i wire them properly in parallel? or series?If parallel which fan in the parallel chain first? (does it matter?)

Hi, all total noob here, Does anyone know how to export a docker container on windows with all the commands attached from kitematic so i can upload it to my synology docker to run a minecraft server? Thanks

Hi guys, was wondering if you could give me an idea of wtf is going on. So ive got Ubiquiti AP-Unifi USG - Netgear 24 prosafe switch - optus modem. The issue ive been experiencing is that some web pages for some reason take a long time to load or dont load at all and on chrome it shows ERR DISCONECTED or something along those lines that shows the webpage doesn't load. But when i say do the same thing on my phone with Optus 4G it loads instantly so i'm not exactly sure if it's on the USG blocking the connection which it didnt before or if it's coming out of Optus internet end. The webpage eventually loads after one or two refreshes...

Yeah I was quite unsure cause the card like extra tall then plus fittings

Hi guys, I was wondering if anyone knew if the MSI GTX 1080TI EK Seahawk edition would fit inside Corsair Crystal 570X case that has a maximus 9 hero motherboard in it. I know this card is very tall but im not exactly too sure if it will

Hi guys, Does anyone know of any third party like corsair etc. DDR3L that i could use to upgrade from 4GB to 8GB instead of buying the expensive Synology Branded Ram?

Well its not the drivers, i just got the latest version of furmark so only conclusion i have is if you guys have a 1080 as well and yours doesnt crash then i can take it back and get a warranty on it asap

Well i dont think it's a furmark issue, because PUBG is crashing heaps and theres artificating in the game when it crashes i also got a blue screen just then " VIDEO SCHEDULER INTERNAL ERROR" Nope, but does it matter? ive got more than enough power for it

Well temps isnt an issue being fully watercooled and voltages shouldnt be an issue either....

Well the system isnt crashing but Furmark freezes and crashes. It doesn't crash without MSAA on though... Thoughts?...