Jump to content

narrdarr

Member
  • Posts

    4,298
  • Joined

  • Last visited

Everything posted by narrdarr

  1. That's nice and all. But I meant not installed. So we can see the heat pipes, cold plate, a paste spread.
  2. Can you take a few pics of the cooler from different angles?
  3. What are the temps with the side panel off?
  4. does the cooler come with a piece of plastic tape on the bottom? did you remove it?
  5. It pretty universal. It should fit but you can always contact them. Also I would just the 3 instead of the 4. The only change is the backplate.
  6. Both nzxt and corsair has there own rgb eco system. So no they will not work with the nzxt controller, but they will work with the motherboard. You'll use asrock rgb software to control them. But your lighting isnt going to sync with whatever the nzxt controller is set to.
  7. Its ok but it is a bit high. Whats your temps with an actual cpu load You can use cinebench r20 to bench Not sure if it's been fix, but in the past hw monitor was causing a raise I temps for reasons I dont want to get it to right now, but use hwinfo instead Things to help bring down temps Update bios and chipset drive Undervolt so long it doesn't cost performance.
  8. I agree with getting a different tge 510 case are terrible. The the options are on the table for premade custom cables, but the places where you would do your own design expect 3 - 4 weeks before you get them.
  9. does event viewer show any errors?
  10. Did you update drivers too? Especially chipset and graphics.
  11. narrdarr

    Fan concept Help

    Literally case by case . LOL I agree
  12. the pump is connected to a fan header so just set the header in the bios to 100%
  13. its fine don't worry about it. just clean it with some rubbing alcohol.
  14. rear should be exhaust aswell. i wouldn't try to worry about positive or negative pressure as the case is pretty closed off in the front as you dont have the p400a just the p400
  15. they are all maglev fan so theyll be the same
  16. Unifans are hard to find at an reasonable price. Id Probably get QL fan over the LL fan do to the fact the QL fans have lighting on both sides of the fan.
  17. I've painted an ar01. I used engine paint with ceramic particles in it to help heat dissipate through the paint. How much did it help? Idk as the cpu I was using didnt require alot to cool.
  18. Not sure what your talking about it a standard front mount aio with the fans in a push config as intake. It fine as it is. The only thing is the tubes look a bit stretched. Does your front panel still go on? You may want to move the fans to the inside of chassis. You can keep the same config. This will allow the tube to be not so tight and still get the rgb lighting throw the front panel.
  19. you said there is a pic of the commander pro and/or lighting node? can you screen shot it?
  20. well i can tell you really want to see as much as the rgb as possible . so before i make any recommendations which lancool do you have?
  21. Yes you can do that. They should send you the rev 2 mounting hardware.
  22. First some of your verbiage for your fan placement is weird. Just to confirm You have 3x fans in a push config as intake on the front with rad 2x exhaust @ the bottom ( but want to be able to flip them over to intake without lossing the rgb) 2x top exhaust 1x rear exhaust fan ? Second Corsair doesn't make reverse flow fans. You'll want their QL or HD fans The QL are double sided with rgb. The HD fans rgb are in the center of the frame but are easily viewed from both Side. Third Corsair icue suite is pretty awesome once you learn how to it. Fyi just set the pump to extreme then make your own fan curve. By default the fan change speed based on water temp not cpu temp. They each have their benefits. And you can change it to whatever. Fourth You should run your voltage as low as possible that is stable for your OC. This is not only better for cooling but also better for the longevity of the cpu. Fifth If you want other fans thermalright has regular and reverse fans that are argb and rgb. But they won't work with icue( at least without hacking them). I also dont recommend mixing rgb suite when possible.
  23. seems about right. But whats your pump speed? you should max it out so long the pump noise noise its bad
  24. its not uncommon to see this, but you could get better temps. makes sure bios and chiset driver are up to date then undervolt a bit.
×